Vinten 3395 Скачать руководство пользователя страница 14

Страница: 14 / 52

Section 2

Installation and Operation

Contents

Para

General

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Installing the head on a tripod

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Mounting the camera

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Mounting the camera (optional Quickfit adaptor)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Balancing the head

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Pan and tilt brakes

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Pan and tilt drag

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

General

To identify components, please refer to

Fig 1.1

. For further operating instructions, please refer to Vision

LF Pan and Tilt Heads Operators Guide, Publication Part No. 3390-8.

Installing the head on a tripod

The Vision 5LF head is supplied with a 100 mm ball base and is designed for installation on a

compatible Vinten Vision tripod.

Adaptors are available which enable the heads to be installed on tripods or pedestals fitted with other

mountings.

To install the head, remove the bowl clamp assembly

(7)

from the head, position the head on the tripod

and refit the bowl clamp assembly from below. Level the head with the aid of the level bubble

(4)

and tighten

the bowl clamp.

Mounting the camera

Remove the slide plate

(6)

from the head by releasing the slide clamp

(1)

, pressing the slide lock

release

(13)

and pulling the plate to the rear.

Attach the slide plate to the camera or camera mounting plate under the approximate centre of the

camera's weight using both fixing screws

(5)

. Position the screws as far apart as possible.

Push the slide plate and camera into the track in the platform, ensuring slide release

(13)

snaps into

position.

Содержание 3395





















































Результаты поиска

Содержание 3395

Отзывы:

Бренды по названию

Популярные бренды

Vinten 3395, Руководство по обслуживанию

Результаты поиска

Содержание 3395

Отзывы:

Бренды по названию

Популярные бренды