Vinten 3320 Скачать руководство пользователя страница 31

Страница: 31 / 53

7.5

Prise hole plug (7) out of clamp knob (4), remove screw (6) and washer (5) and take off clamp

knob.

7.6

Unscrew spindle (3) from outer tube.

7.7

Remove the top housing covers (25) by springing the sides apart and pulling them away from the

outer tube. The top housing cover springs (26) are attached to bosses in the cover and must be
removed with care.

Skid

Centre casting and leg assemblies

To dismantle the centre casting and leg assemblies (

Fig 6.5

8.1

Separate the telescopic column from the skid (

Section 2

8.2

Turn the skid upside down and unfold the legs.

8.3

Remove screw (25) and five screws (23) and separate upper and lower centre castings (2) and

(24).

8.4

Lift out folding legs (30) and collect leg tube lock plungers (26), springs (27), leg tube pads (28)

and nylon washers (29).

8.5

Lift out fixed leg (22) which is located in the skid casting by bosses which engage holes in the

leg.

8.6

Remove rubber securing strap (3) from foot support (5).

8.7

If fitted, remove cable guards (15) by taking off adjusting knob (16) and removing screw (12) and

washers (13) and (14). Slide off cable guard.

Castor assemblies

To remove the castor assembly (

Fig 6.5

9.1

Separate the telescopic column from the skid (

Section 2

9.2

Remove two screws (4) which secure foot support (5) to the leg assembly and remove foot

support.

9.3

Use tool

3319-900SP

through the hole in the top of the leg tube to remove nut (6). Note that nut

is secured with Loctite 242.

9.4

Remove castor assembly (19) or (31) and collect washer (7) from inside leg tube.

NOTE:

Both types of skid assembly are covered in the following procedure with reference to
variations as they occur.

NOTE:

The skid leg locking plungers (26) are held under slight spring compression by the skid
centre castings. Take care not to lose items during dismantling.

Содержание 3320






















































Результаты поиска

Содержание 3320

Отзывы:

Бренды по названию

Популярные бренды

Vinten 3320, Руководство по обслуживанию

Результаты поиска

Содержание 3320

Отзывы:

Бренды по названию

Популярные бренды