manualshive.com logo in svg

Vinten 3320, Руководство по обслуживанию

Поделиться
Скачать
Vinten 3320 Скачать руководство пользователя страница 29

29

Contents

Previous 

Page

First 

Page

Next 

Page

Previous 

View

4.2

Remove four retaining screws (2), rubber washers (4), washers (5) and Nyloc nuts (6) which 

secure the steering ring (3) to the top tank plate and remove steering ring. Discard Nyloc nuts and 
renew during assembly.

4.3

Remove two screws (24) which secure shaft guide (23) to top tank plate.

4.4

Withdraw control valve switchover shaft (22) complete with shaft guide (23) from top tank plate.

4.5

Remove 'O' rings (25) and (26) from the switchover shaft and discard. 

4.6

Remove grub screw (27) from tank top plate.

4.7

Withdraw valve spring (28), valve (29) and 'O' ring (30) from top tank plate. Discard 'O' ring (30).

4.8

Remove screw (11) and remove catch lever bracket (13) complete with catch lever (10). Collect 

locating ball (14) and spring (15).

4.9

Apply short pieces of adhesive tape or similar non-abrasive marking to relief valve assembly and 

tank tube to indicate orientation for assembly.

4.10 Remove four countersunk socket head screws (43) from lower end of tank assembly and 
withdraw tank lower end plate (40) complete with pressure relief valve assembly and 'O' rings (41) and 
(42).

4.11 Remove and discard 'O' rings (41) and (42).

4.12 Withdraw ram cylinder (44) and piston rod assembly (34, 35, 36) from tank tube (45).

4.13 Withdraw piston rod assembly (34, 35, 36) from ram cylinder (44).

4.14 Hold open the tines of the piston head (34) and remove the piston valve (32).

4.15 Break the Loctite seal and remove 'O' ring (33) from the piston valve. Discard the 'O' ring and 
remove remaining traces of adhesive from piston valve (32).

4.16 Remove 'O' ring (31) from piston head and discard.

4.17 Note orientation and remove eleven 'O' rings (37), cylinder sleeve (39) and nine plain washers 
(38) from the piston rod. Examine 'O' rings and replace if damaged.

NOTE:

Grub screw (27) is secured with Loctite and is under slight spring compression. Take care 
not to lose items during dismantling.

NOTE:

Locating ball (14) and spring (15) are retained by catch lever (10) with the spring under 
compression.

WARNING!:  Do not remove or attempt to adjust the pressure relief valve.

Содержание 3320






















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды