Vinten 3320 Скачать руководство пользователя страница 24

Страница: 24 / 53

Bottom clamp adjustment

When applied finger-tight, the ‘V’ notch on the bottom clamp knob should be within the limits shown. To

adjust the bottom clamp (

Fig 4.1

6.1

Tighten the clamp finger-tight.

6.2

Remove the hole plug

. Remove the screw

and washer

securing knob

to the spindle

6.3

Remove the knob, turn counter-clockwise, then replace on spindle

(5)

so that the ‘V’ notch on the

clamp knob is within the limits shown.

6.4

Degrease screw

(2)

, coat with Loctite 222E and secure knob with washer

(3)

and screw

(2)

Replace hole plug

(1)

Top clamp and skid clamp adjustment

The top clamp and skid clamp are applied and released by turning the handle clockwise or counter-

clockwise. Both handles have push-on/pull-off type ratchet adjustment.

To adjust the top and skid clamps pull the clamp handle away from the spindle, rotate it clockwise and

release.

Repeat the above procedure, as necessary, until the clamp locks when applied but allows free

movement when released.

Fig 4.2 Elimination of radial and side play on the top stage

(1)

(2)

Содержание 3320






















































Результаты поиска

Содержание 3320

Отзывы:

Бренды по названию

Популярные бренды

Vinten 3320, Руководство по обслуживанию

Результаты поиска

Содержание 3320

Отзывы:

Бренды по названию

Популярные бренды