background image

 

                                                       

 

                       

 

- 7 - 

4) Alarm Signals 
 

The alarm codes are described as follows.  

 

MESSAGE 

CAUSE 

FUNCTION 

P1

 

Temperature probe faulty 

Compressor switching to Con and CoF  

HA

 

High temperature alarm

 

Probe temperature ALU higher than the 

setting temperature; Outputs unchanged 

LA

 

Low temperature alarm 

Probe temperature ALL lower than the 

setting temperature; Outputs unchanged 

CA 

External alarm 

All outputs off  

 

Probe  alarms  P1”,  start  a  few  seconds  after  the  fault  in  the  related  probe;  they 
automatically  stop  a  few  seconds  after  the  probe  restarts  normal  operation. 
Check  connections  before  replacing  the  probe.  Temperature  alarms  “HA”,  “LA” 
automatically  stops  as  soon  as  the  temperature  returns  to  normal  value.  Alarm 
“CA” (with i1F=PAL) recovers only by switching off and on the instrument.  

 
2.  Temperature Setting 
 

  Set the temperature at 55 

°

F

 for the optimum aging of wine 

  On  initial  start-up,  the  time  required  to  reach  the  desired  temperature  will 

vary,  depending  on  the  quantity  of  bottles,  temperature  setting  and 
surrounding temperature. 

  Allow 24 hours to stabilize the temperature for each new temperature setting 

operation 

 

3. How to see temperature set-point 
 

1) Press and immediately release the 

SET

 key, the display will show the set-point 

value. 
2) Press again and immediately release the 

SET

 key to display the probe value.  

 

4. How to change the set-point  
 

1) Press and hold the 

SET

 key until the “°C” or “°F” LED starts flashing and the 

set-point is displayed.  
2) Press the up/down keys 

/

  to change the set-point value within 10 sec.  

3) Press the 

SET

 key again to store the new set-point value. 

 

NOTE 

The  unit  turns  on  at  set-point  Set  plus  regulation  differential 
Hy after anti-short cycle AC has elapsed; the unit turns off at 
set-point Set

.

 

 
 
 

Содержание WINE-MATE WM-4500DS































Отзывы: