Vingtor Stentofon ECPIR-3P Скачать руководство пользователя

Страница: 27 / 80

Turbine Station Configuration Guide

A100K11194

5.3 Audio Settings

● Select

Advanced ICX-AlphaCom

Audio

● Select or set values for the parameters

Volume Override Level

Select the Volume Override Level in the range 0 to 8 from the drop-down box. The default

setting is 7.

Microphone Sensitivity

Select the sensitivity level in the range 0 to 7 from the drop-down box. The default setting is 4.

If used as a local PA panel, a setting in the 1 to 3 range will reduce the chance of acoustic feed

back (howling).

Digital/Analog Mic Switch

Switches from Digital to Analog Mic based on settings.

Options:

Always Digital

(Default),

Always Analog

Analog I/O Pin

Analog I/O Pin Call End

Mute speaker while analog mic

Voice Engine Mode

Voice

: Regular audio quality (default).

HD-Audio

: Play audio in PCM L16/48kHz format. Use

HD-Audio

only on devices that handle

high quality music streaming/playback, typically IP loudspeakers and Turbine kits used as PA

interface.

Volume Control Ch1/Ch2

Offset Gain (default routed to Amplifier/Speaker)

Valid range: -62 to +24 dB

Содержание ECPIR-3P

















































































Результаты поиска

Содержание ECPIR-3P

Отзывы:

Похожие инструкции для ECPIR-3P

Бренды по названию

Популярные бренды

Vingtor Stentofon ECPIR-3P, Техническое руководство

Результаты поиска

Содержание ECPIR-3P

Отзывы:

Похожие инструкции для ECPIR-3P

Бренды по названию

Популярные бренды