6
SW24.D
EN
4.5 - Stop push-button
99
52
63
51
99 61 62
COM
STOP
5 - Control panel programming
5.1 - Preliminary operations
After powering the unit, the name of the control board written as
SW2.D, the firmware version FX.XX and 3 flashes with the word FLSH
appear in the display, then display then goes off.
To function correctly, the control panel requires some minimum and
essential settings and checks.
- Input status check:
Check the diagnostic LEDs of the inputs, the LEDs 61, 62, 63 must be
on.
If one of the safety inputs (61, 62, 63) is not used, insert a bridge
between the common (99) and the unused input.
If one of the safety inputs (61, 62, 63) is open, the dot at bottom right-
hand corner of the display flashes to indicate a engaged/non-working
safety that will prevent the gate from moving. It will therefore be neces-
sary to check the connections and the correct functioning status of the
safety devices.
- Gate travel calibration
The control panel must know some physical parameters of the gate in
order to function correctly. The operation allowing the control panel to
know these physical gate parameters is called travel calibration. If this
is not done, the control panel may not perform slowdowns or detect
obstacles correctly.
5.2 - Using the display
Button
Description
OK
Button to turn on the display, to access the menu and to
confirm the parameter value change. When the motor is
moving, when pushed once it displays the absorption in A of
motor M1, when pushed twice it displays the absorption in A
of motor M2
▲
Button to scroll up the menus and increase the parameter
value
▼
Button to scroll down the menus and decrease the param-
eter value
ESC
Button to turn off the display, exit the menu and cancel the
parameter value change
51
Step-by-step command button
5.3 -
Menus
The control board programming is organized in menus and submenus
that allow to access and edit the parameters and logics of the control
board. The control board features the following first level menus:
Menu
Description
LRNE
Quick gate travel calibration
LRNA
Advanced gate travel calibration
PAR
Control board parameter setting menu
RAD
Remote controls management menu
DEF
Factory reset menu
CNT
Cycle counter menu
ALM
Board alarms menu
PASS
Board protection level setting menu
Submenus
All submenus are described in the table below.
LRNE
Quick gate travel calibration.
The calibration is fully self-performed and sets:
- Opening and closing slowdown to 30% of the total travel
- Opening delay between leaves to 3 s
- Closing delay between leaves to 6 s
It requires mechanical stops both on opening and closing
Rows highlighted in grey refer only refer to a double leaf in-
stallation, in a single leaf installations delays between leaves
are not programmed
Button Display
msg
Phase description
-
51
Wait for calibration procedure start
51
CLS2
When button pressed: leaf 2 closing and
search for leaf 2 closing stop
-
CLS1
Leaf 1 closing and search for leaf 1 closing
stop
-
LOC
Electric lock activation to free leaf 1
-
OPN1
Leaf 1 opening travel measurement at slow
down speed
-
OPN2
Leaf 2 opening travel measurement at slow
down speed
-
CLS2
Leaf 2 closing at normal speed and then at slow
down speed up to leaf 2 closing mechanical stop
-
CLS1
Leaf 1 closing at normal speed and then at slow
down speed up to leaf 1 closing mechanical stop
-
oooo
Full opening and closing of both leaves for cur-
rent thresholds measurement
-
END
End of procedure
LRNA
Advanced gate travel calibration.
Calibration allows the installer to set:
- Opening and closing slow down position
- Leaves end of travel positions
- Opening and closing delays between leaves
- Pedestrian opening position
It requires mechanical stops on closing only
Rows highlighted in grey refer only refer to a double leaf in-
stallation, in a single leaf installations delays between leaves
are not programmed
Button Display
msg
Phase description
-
51
Wait for calibration procedure start
51
CLS2
When button pressed: leaf 2 closing and
search for leaf 2 closing stop
-
CLS1
Leaf 1 closing and search for leaf 1 closing
stop
-
LOC
Electric lock activation to free leaf 1
51
OPN1
Leaf 1 opening start.
When button pressed: leaf 1 opening slow
down position setting, the leaf proceeds at
slow down speed
