manualshive.com logo in svg

Viking VUIM/DUIM150, Руководство по обслуживанию

Поделиться
Скачать
Viking VUIM/DUIM150 Скачать руководство пользователя страница 24

© 2009 Viking Preferred Service 

24

Removing the Condenser 

(continued)

10.  Remove fan by removing the two nuts on fan 

mounting bracket at the baseplate. The fan wire 
leads can be left. connected. Set fan assembly 
to side of mechanical.

11.  Remove the three nuts retaining the side of the 

fan shroud. Remove the fan shroud.

12.  Unbraze the capillary tube from the drier 

assembly.

13.  Unbraze the hot gas valve tube at the tee on 

the drier assembly (see 

Figure 4

).

14.   Unbraze and remove the drier assembly.

15.  Unbraze the hot gas line from the compressor 

at the top of the condenser coil (see 

Figure 11

).

Installing the Condenser

Reverse the removal procedure. Be sure to 
thoroughly flush the system and evacuate to 50 
microns before weight charging. If contamination 
was found or determined, the evaporator should 
also be replaced at this time.

Drain Valve

The drain valve drains water that is left in the 
reservoir after ice production. The valve will only 
be open for a fixed time of 45 seconds during the 
beginning of the harvest cycle.

The drain valve fails by allowing water to flow into 
the drain during the ice production cycle (leak-
by). This can be caused by a foreign particle(s) or 
build-up of mineral deposits that will not allow 
the valve to fully seat or has caused damage to 
the seat of the valve. Periodic cleaning of the ice 
machine will keep build-up off the valve allowing it 
to work properly and should be done before further 
evaluation of the valve.

Symptoms of this include thin or no ice slab 
(depending on severity of leak) and, more 
noticeably, water drainage through to the drain 
during ice production cycle (do not mistake this for  
reservoir run-off water or melted ice drain 
water from the ice bin). The drain valve should be 
replaced if it is found to be leaking.

The drain valve solenoid actuator can also possibly 
fail. Test the solenoid by checking the resistance. 
A resistance of 50-65 ohms should be found. If no 
resistance is found, the drain valve will need to be 
replaced.

 

Service Diagnostics and Procedures 

(Sealed System Components/Valves)

Содержание VUIM/DUIM150












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды