FEBERARY/06/2006
Factory defaults setting to press the
button twice to start the vehicle.
Programming this feature to eliminate an accidental remote start, when kids enter this transmitter, it
requires: The user presses the transmitter
and buttons at the same time to start the vehicle.
START FEATURE “
II
” PRORAMMING:
1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
th
2. Push the Valet switch
10
times and holding in on the
10
push until
five
chirps with a long chirp is
hearing then release the valet switch. You are now in the Start feature
‘II’
programming mode.
3. Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to program.
Four Chirps /
One Chirp /
Two Chirps /
Three Chirps /
Press
LED four pulse
LED one pulse
LED two pulse
LED three pulse
T
ransmitte
r
Button
Factory Default
Setting
Exit the programming mode. (3 long chirp & 3 parking light flashes to confirm this exit.)
1
2
+
Engine Checking
TACH.
Engine Checking
Voltage
Engine Checking
OFF
RPM learning
3
Start Timer:
0.8-second (2 chirps), 1.0-second (3 chirps), 1.2-second (4 chirps),
1.4-second (5 chirps), 1.6-second (6 chirps), 1.8-second (7 chirps),
2.0-second (8 chirps), 3.0-second (9 chirps), 4.0-second (10
chirps),
0.6-second
Low check level
Hi check level
4
Start / Stop the system for TESTING & ADJUSTMENT
5
-
Exit
:
Press the
button on the transmitter. A 3 long chirps & 3 parking light flashes to confirm exit.
ENGINE CHECKING TACH. / RPM LEARNING
Important Note:
You must program the “Tach Signal” before trying to remote start.
1. Turn the Ignition switch ‘ON/OFF’
3
TIMES and stay in
OFF
position.
th
2. Push the Valet switch
10
times and holding in on the
10
push until
five
chirps with a long chirp is
hearing then release the valet switch.
and
3. Press and release the transmitter
buttons at the same time once to set the “Engine
Checking TACH.” [1] LED flash, [1] chirp to confirm this setting.
4. Press and release the transmitter button once, [1] LED flash, [1] chirp to indicate the system in
features “RPM Learning mode”.
5. Start the vehicle with the key. (While the engine is running, the parking light & LED will flash, If don’t,
please check tachometer White/Red wire connection.
(H6/7)
6. Press and hold the valet switch for 2 seconds until a long chirp and the LED light constant for two
seconds. The RPM signal is learned.
7. Turns off the ignition switch to stop engine running.
Once you complete step 7, you can adjust and test “Check Level” as below:
CHECK LEVEL PROGRAMMING: (TEST and ADJUST)
1. Press the
button twice on the transmitter to start the vehicle.
2. If everything goes well:
a. Press the
button twice on the transmitter to stop engine running. You have been completed this
programming successfully.
b. Press button on the transmitter to exit the program mode. There will be 3 long chirps & 3 parking
light flashes for confirmation.
3. If the crank time is too short, (The engine did not successfully run before the starter quit cranking):
button on the transmitter to turn ignition lights “OFF”.
a. Press the
button on the transmitter to set proper “Check Level ” to Hi position. [2] LED flashes,
Press
[2] chirps to confirm this setting
b. Repeat the step1 – 4.
4. If the crank time is too long, (Engine is successfully running, while the starter is still cranking):
button on the transmitter to stop engine running.
a. Press the
Press
button on the transmitter to set proper “ Check Level ” to Low position. [1] LED flash,
[1] chirp to confirm this setting
b. Repeat the step1 – 4.
ENGINE CHECKING VOLTAGE
560A
14
