background image

7

© 2012 Viking Preferred Service 

Operation

adjusting Controls (cont.)

If you need to adjust the temperature in either the 

refrigerator or freezer compartment, use the settings 

listed in the chart as a guide.

To adjust Set point Temperatures:

The first touch of the (+) or (-) touch pad displays the 

current temperature set point.

•    Press the (+) or (-) touch pads until the desired 

temperature set point is displayed.

note: 

Except when first turning on the refrigerator, 

DO NOT adjust either temperature control more 

than one setting at a time. Wait 24 hours between 

adjustments for the temperature to stabilize.

Temperature adjustment Chart

Condition/Reason

Adjustment

Refrigerator too warm

Adjust REFRIGERATOR 

Control 1° lower

Freezer too warm/too little 

ice

Adjust FREEZER Control 

1° lower

Refrigerator too cold

Adjust REFRIGERATOR 

Control 1° higher

Freezer too cold

Adjust FREEZER Control 

1° higher

additional Control Center Features

 humidity  Control

The Humidity Control feature turns on a heater to 

help reduce moisture on the door hinge seal. Use in 

humid environments or when you notice

moisture on the door hinge seal. The refrigerator 

uses more energy when Humidity Control is on.

•    Press Humidity Control when the 

environment is warm and more 

humid, or if you notice moisture on 

the door hinge seal. The indicator 

light will be lit when humidity 

 

control is ON.

•    Press Humidity Control again to 

 

turn OFF and save energy when 

 

the environment is less humid.

Sabbath Mode 

The Sabbath Mode is designed for those whose 

religious observances require turning off the lights 

and dispensers.

 

ON - All interior lights and alarm tones will be 

disabled. 

OFF - All interior lights and alarm tones will be 

enabled.

•    Press and hold the Sabbath Mode 

touch pad for 3 seconds or until 

 

the indicator light is lit to turn on 

 

this feature. Press and hold the 

Sabbath Mode touch pad again to 

turn off this feature.

Door alarm

The Door Alarm feature sounds a chime every few 

seconds when the refrigerator door has been left 

open for 5 continuous minutes. The chime will

sound until the door is closed or Door Alarm is 

turned off.

•    Press the Door Alarm to turn this 

feature ON or OFF. The indicator light 

will be lit when the Door Alarm feature 

is on.

Max Cool

The Max Cool feature assists with periods of high 

refrigerator use, full grocery loads, or temporarily 

warm room temperatures.

•   Press Max Cool to set the freezer and 

refrigerator to the lowest temperature 

settings. Press Max Cool again to 

return to the normal refrigerator set 

point.

note: 

The Max Cool feature will automatically shut 

off in approximately 12 hours.

Filter Reset

 The Filter Reset control allows you to restart the 

water filter status tracking feature each time you 

replace your water filter. See “Water Filtration 

System.”

•    Press and hold the Filter Reset touch 

pad for 3 seconds, until the Order 

 

or Replace light turns off.

 

Содержание RDDFF236



























































Отзывы: