manualshive.com logo in svg

Viking F20712D, Руководство по установке, Страница: 12 / 20

Поделиться
Скачать
Viking F20712D Скачать руководство пользователя страница 12

12

Remove and Replace Handles

1. Using a 3/32"or 1/8” hex wrench, loosen the

two set screws located on the side of each
handle. 

2. Pull the handle straight out from the door.

Make sure you keep the screws for reattaching
the handles.

3. To replace the handles, reverse the directions.

Remove Doors and Hinges

IMPORTANT

:

• Remove food and any adjustable door or utility

bins from doors.

• Keep the refrigerator doors closed until you are

ready to lift them free from the cabinet.

NOTE:

Provide additional support for the

refrigerator door while the hinges are being
removed. DO NOT depend on the door gasket
magnets to hold the door in place while you are
working.

TOOLS NEEDED:

5/16", 3/8", 1/4" hex-head

socket wrench, #2 Phillips screwdriver, and a flat-
blade screwdriver.

1. Unplug refrigerator or disconnect power.
2. Remove the base grille. Grasp the grille firmly

and pull it toward you.

3. Starting with the right-hand side door, remove

the parts for the top hinge as shown in Top
Hinge graphic. Lift the refrigerator door from
the bottom hinge pin.

4. Remove the shim from the bottom hinge pin

and keep it for later use. See Bottom Hinge
graphic.

5. Remove top hinge cover from left side

refrigerator door. Disconnect the wiring plug
located on top of the hinge by wedging a flat-
blade screwdriver or your fingernail between
the two sections. See Connections graphic.

.

Doors & Drawer Removal

Remove Doors and Hinges 

(cont.)

6. Disconnect the water line by holding the tabbed

section of the water line while turning the black
locking collar clockwise. See Connections graphic.

OR

6a.Disconnect the water line by pulling back on the 

locking collar while pulling the water line out of 
the water line connector. See Connections 
graphic.

7. Remove the parts for the top hinge as shown in

Top Hinge graphic. Lift the left-hand side door
from the bottom hinge pin. 

NOTE: 

On some models, remove the shim from

the bottom hinge pin and keep it for later use.
See Bottom Hinge graphic.

8. Using a 3/8" hex wrench, remove the leveling leg

brackets from the bottom of the cabinet. Keep
screws for later use.

Top Hinges

A. Shim (on some models)

C. Hinge Screws

B. Bottom Hinge

Bottom Hinges

A

B

C

Connections

B. Wiring Plug

A. Tabs

A

B

A. Hinge Cover Screw
B. Top Hinge Cover
C. 

5

/

16

" Hex-Head Hinge Screws

D. Top Hinge

B

A

C

D

Connections

A

B

A. Wiring Plug
B. Water Line Connection

6

6a

OR

Содержание F20712D





















Отзывы:

Нет отзывов