F. Wiring the E-50 Camera
VIKING
Model:
E-50-SS
26703A
Serial No:
REN 0.8A:
XXXXXXXX
V
iking Electronics, Inc. (715) 386-8861
1531 Industrial St., Hudson, WI 54016
P/N:
DEV
:
Complies with FCC Part 15 and 68 Reg. No: US:AH3TE08A22264
Back View of the E-50 Circuit
Board Mounting Plate
Yellow (Video)
- Black (GND)
+ Red (6VDC)
Green (Tip)
Red (Ring)
** Camera Pwr (+)
Orange
** Camera GND (-)
W/O
Video GND (-)
Green
Video Out (+)
W/G
* Up to 150 ft
3-Wire Gel-Filled Butt
Connectors included
(3M Scotchlok UR2)
CAT5E or
CAT6 Cable
(see Caution below)
Phono (RCA) Plug,
F Connector, Etc.
(+)
(-)
To unused input on TV, VHF
modulator, whole house video
distribution equipment, IP video
encoder (Axis M7001), etc.
Phone Board
Audio Out
W/BL
Phone Board
Audio Out
Blue
Video Out (+)
Video GND (-)
See page 4, section E
Wiring Phone Board
Blue W/BL
W/G Green
W/O
Orange
120V AC
Camera GND (-)
Camera Power (+)
Black with
White Stripe
5V DC Adapter
(included)
Black
(-)
!
(+)
(4) Crimp-on Splice
Connectors (not included)
* Note:
Up to 150 ft video cable run length can be achieved using CAT5E or CAT6 cable. Longer cable runs can be used if a passive or active video
Balun transceiver is used on each end of the cable. Generally, passive transceivers can achieve up to 750 ft cable runs where active transceivers
can achieve up to 3000 ft runs depending on cable type, etc. The type of video balun transceiver required is specific to your cable run length. For
more information on video balun transceivers go to: www.northernvideo.com.
Caution:
When routing CAT5E or CAT6 cable, maintain a minimum distance of 3 ft from any parallel high voltage wire (110 VAC) and a minimum of
2 ft from crossing any high voltage wire. For installations where RF noise is expected (commercial applications) or wire runs are near high voltage
(110 VAC) wires, a shielded video cable such as RG6 is recommended.
G. Adjusting the Camera
The camera can be tilted and rotated to your desired
position. A portable service (test) monitor can be used to
determine the correct viewing angle during installation.
Important:
To prevent the edge of the faceplate from
being viewed in the video image, do not rotate the cam-
era beyond 30 degrees or tilt beyond 20 degrees.
Vertical (Tilt)
Adjustment
+/- 20 degrees
maximum
Horizontal (Rotation)
Adjustment
+/- 30 degrees maximum
5
** Note:
The maximum camera power supply wire run length is 250 ft of 24 gauge wire (CAT 5/6), longer runs are possible by doubling pairs, increas-
ing the wire gauge or using a 6V DC 200mA power adapter (Viking part # L122110). Go to www.vikingelectronics.com and click on “Spare Parts”.
1. Using RG59 for Video and CAT5 for Camera Power and Phone Board Audio (Recommended)
2. Using CAT5E or CAT6 for Video, Camera Power and Phone Board Audio (see Caution below)
VIKING
Model:
E-50-SS
26703A
Serial No:
REN 0.8A:
X
XXXXXXX
V
iking Electronics, Inc. (715) 386-8861
1531 Industrial St., Hudson, WI 54016
P/N:
DEV
:
Complies with FCC Part 15 and 68 Reg. No: US:AH3TE08A22264
Back View of the
E-50 Circuit Board
Mounting Plate
** Camera Pwr (+)
Orange
** Camera GND (-)
W/O
Yellow (Video)
3-Wire Gel-Filled Butt
Connectors included
(3M Scotchlok UR2)
CAT5 Cable
To unused input on TV,
VHF modulator, whole
house video distribution
equipment, IP video
encoder (Axis M7001), etc.
120V AC
Camera GND (-)
Camera Power (+)
Black with
White Stripe
5V DC Adapter
(included)
Black
(-)
!
(+)
Phone Board
Audio In/Out
W/BL
Phone Board
Audio In/Out
Blue
See page 4, section E
Wiring Phone Board
Blue W/BL
W/O
Orange
*** RG59 or RG6 Shielded
Video Cable, up to 1000 ft
Center conductor
stripped back 5/8"
Twisted foil and braided shield
** Up to 250 ft
"F"
Connector
"F" to Phono Plug
Adapter
(Radio
Shack part #278-252)
- Black (GND)
+ Red (6VDC)
Green (Tip)
Red (Ring)
Crimp-on Splice
Connectors (not included)
OR
Black
Yellow/Red
**** Female "F" to Wire or "BNC" to Wire
Converter Cable
(not included)
**** For ease of installation, a Viking Female
"F" to Wire Converter Cable can be used (Part
# 261217) or "BNC" to wire converter cable
(Part # U213510) can be used. Go to
www.vikingelectronics.com and click on
"Spare Parts" to order.
IMPORTANT:
Electronic devices are susceptible to lightning and power station electrical
surges from both the AC outlet and the telephone line. It is recommended that a surge pro-
tector be installed to protect against such surges.
!
*** Note:
RG59 or RG6 with solid center conductor and 95% bare copper braid shield.
