I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n
B. Old Work / Remodel Flush Mounting
(Using a recommended Allied Molded 9331 Rough-In Box)
A. New Construction Flush Mounting
Step 1.
Recommended mounting height to bottom of the rough-in box is 50” - 54”. Front of box should stick out approximately
½" from front surface of wall stud (this may vary depending on the walls sheathing and siding thickness).
Caution:
Rough-In box must be mounted
LEVEL
and must
NOT
stick out beyond the front surface of siding.
Step 2.
To maintain a vapor barrier on outside wall applications, caulk around the box, filling any gaps between the box and the
rough opening. Apply caulk to any holes in the box around wires, etc.
Step 3.
When installing siding cut a hole just large enough for the Rough-In box opening.
Caution:
Too large of a hole can
cause plate misalignment and compromise the gasket seal.
Note:
When mounting to 4 inch or less horizontal lap
siding, the unit can be mounted horizontally (see page 5, section
H
) flush against siding or a siding mounting block
can be used (recommended with vinyl siding). Contact siding installer for the correct mounting block.
Step 1.
Recommended mounting height to bottom of the rough-in box is 50” - 54”. Make sure mounting location is free of wall
studs, wires, etc.
Step 2.
Place Rough-In box
LEVEL
against siding. Trace outline of box onto siding.
Note:
When mounting to 4 inch or less
horizontal lap siding, the unit can be mounted horizontally (see page 5, section
H
) flush against siding or a siding
mounting block can be used. Contact your siding Installer for the correct mounting block part number.
Note:
A siding
mounting block is recommended when mounting to vinyl siding.
Step 3.
Cut a hole through the siding and wall sheathing just large enough for the rough-in box.
Caution:
Too large of a hole
can cause plate misalignment and compromise the gasket seal.
Step 4.
The front surface of the Rough-In box can be mounted flush against wood siding or can be recessed and mounted
flush against wall sheathing when mounting on aluminum, steel or vinyl siding.
Step 5.
When mounting to 5/8 inch thick or less wall sheathing the two attached screws with wing brackets can be used to
secure the rough-in box. When mounting to surfaces thicker than 5/8 inch, four standard flat head dry wall screws can
be used to secure the Rough-In box through its mounting ears (see page 4 section
D
).
Step 6.
To maintain a vapor barrier on outside wall applications, caulk around the box, filling any gaps between the box and
the rough opening. Apply caulk to any holes in the box around wires, etc.
F
F
e
e
a
a
t
t
u
u
r
r
e
e
s
s
O
O
v
v
e
e
r
r
v
v
i
i
e
e
w
w
VIKING
Model:
E-50-SS
26703A
Serial No:
REN 0.8A:
XXXXXXXX
V
iking Electronics, Inc. (715) 386-8861
1531 Industrial St., Hudson, WI 54016
P/N:
DEV
:
Complies with FCC Part 15 and 68 Reg. No: US:AH3TE08A22264
Color Video Camera:
Wide operating
temperature range of -30°F to 150°F, NTSC
composite video output with 420 lines of
resolution, 70° wide viewing angle lens, tilt and
swivel adjustments for aiming towards visitors.
Speaker Screen:
Stainless steel speaker
screen with 0.018" diameter holes to prevent
punctures from paperclips, etc.
Faceplate:
18 guage 304 stainless steel or 16
gauge polished brass faceplate with super
durable UV stable powder paint to prevent
fading and resist scratching.
Protective Camera Window:
Impact resistant
polycarbonate lens with scratch resistant
coating and water-tight gasket.
Speaker:
Mylar speaker with rubber gasket to
maintain water-tight seal and eliminate water
deterioration.
Microphone:
Omni-directional microphone
with protective water-resistant cloth.
Mounting Screws:
6-32 x 1.25" long flathead
with 5/64" hexdrive, 18-8 stainless steel to
prevent corrosion.
Push Button Switch:
Push to initiate call, push again to
disconnect. Solid 304 stainless steel internally sealed per IP67.
Faceplate Gasket:
1/4"
thick closed cell PVC to
water-tight seal faceplate,
speaker, switch and
microphone.
Speaker Volume
Microphone Volume
Dip Switches:
1. Auto Answer
2. Dial Tone Detection
3. Programming
4. LED On/Off
Entry Phone Board:
Compact analog speaker
phone with call progress
detection for automatic
disconnect.
Blue LED:
Helps locate the push button in dark
locations, indicates paging and off-hook conditions.
3
The
E-50
is designed to be flush mounted into a standard single gang rough-in box with minimum inside dimensions of 2.25” deep x 2.00”
wide x 2.84” tall. The
E-50
can also be surface mounted in a Viking model
VE-3x5
(not included, see
DOD# 424
).
WARNING:
Do
NOT
use a typical “wet location box” as not all styles seal properly with the
E-50
faceplate.
