1
2
3
4
5
6
7
8
9
1
0
1
1
Z3
Z3
Z2
Z2
R
5
R
2
R4
R4
R7
R7
R9
R9
R8
R8
CR
CR
2
*
Gel-Filled Butt
Connectors (included)
Red
Black
1/2" Close Nipple
Faceplate
Foam
Gasket
Weatherproof
Box
(2) 6-32 x 3/4" screws
(2) Knockout
Plugs
Red
Black
LDB-3
Control Module
*** Blue Strobe
Light
Foam
Gasket
Strobe
Mounting Ring
(2) 10-32 x 3/8" self
tapping screws
(2) 7/8" Nylon
spacers
** Nipple
1/2" x close
A. Installing the Strobe Light Using the Included Weatherproof Box
S1
1
2
ON
3
11
10
9
8
7
6
5
4
3
2
1
* Gel-Filled Butt
Connectors (included)
Note: Polarity Sensitive!
(-) Black with
White stripe
120V AC
(+) Red with
Black stripe
(+) Black
(-) Black with
White stripe
Red
Black
Orange
Purple
Yellow
Blue
Blue
Gray
Brown
Green w/ Yellow Stripe
Red w/ Yellow Stripe
Switched 12VDC Output
(Strobe Light Power)
Relay Contacts
Disable/Info Switch Input
To Terminal Device/Phone
To C.O. Line or Analog
PABX/KSU Station
Normally Closed
Common
Normally Open
1
2
3
4
5
6
7
8
9
1
0
1
1
Z3
Z3
Z2
Z2
R
5
R
2
R4
R4
R7
R7
R9
R9
R8
R8
CR
CR
2
4.60
2.50
2.84
1.50
0.6
1.05
2.0
2.75
4.4
4.0
12V DC
adapter
(included)
LDB-3 Control Module
Back view of weatherproof
single gang box (included)
IMPORTANT:
Electronic devices are susceptible to lightning and power station electrical surges from both the AC outlet and the telephone
line. It is recommended that a surge protector be installed to protect against such surges.
!
Side View of the
Strobe Light (included)
I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n
* Note:
The gel-
filled (water tight)
butt connectors are
designed for insula-
tion displacement.
Do not strip wires
prior to terminating.
* Note:
The gel-filled (water tight) butt connectors are designed
for insulation displacement. Do not strip wires prior to terminating.
W
W
a
a
r
r
r
r
a
a
n
n
t
t
y
y
IF YOU HAVE A PROBLEM WITH A VIKING PRODUCT, PLEASE CONTACT: VIKING TECHNICAL SUPPORT AT (715) 386-8666
Our Technical Support Department is available for assistance weekdays between 8 a.m. and 5 p.m. central time. So that we can give you better service, before you call please:
1.
Know the model number, the serial number and what software version you have (see serial label).
2.
Have your Technical Practice in front of you.
3.
It is best if you are on site.
RETURNING PRODUCT FOR REPAIR
The following procedure is for equipment that needs repair:
1.
Customer must contact Viking's Technical Support Department at 715-386-8666 to obtain a Return Authorization (RA) number. The customer MUST have a complete description of the problem, with all
pertinent information regarding the defect, such as options set, conditions, symptoms, methods to duplicate problem, frequency of failure, etc.
2.
Packing: Return equipment in original box or in proper packing so that damage will not occur while in transit. Static sensitive equipment such as a circuit board should be in an anti-static bag, sandwiched
between foam and individually boxed. All equipment should be wrapped to avoid packing material lodging in or sticking to the equipment. Include ALL parts of the equipment. C.O.D. or freight collect
shipments cannot be accepted. Ship cartons prepaid to:
Viking Electronics, 1531 Industrial Street, Hudson, WI 54016
3.
Return shipping address: Be sure to include your return shipping address inside the box. We cannot ship to a P.O. Box.
4.
RA number on carton: In large printing, write the R.A. number on the outside of each carton being returned.
RETURNING PRODUCT FOR EXCHANGE
The following procedure is for equipment that has failed out-of-box (within 10 days of purchase):
1.
Customer must contact Viking’s Technical Support at 715-386-8666 to determine possible causes for the problem. The customer MUST be able to step through recommended tests for diagnosis.
2.
If the Technical Support Product Specialist determines that the equipment is defective based on the customer's input and troubleshooting, a Return Authorization (R.A.) number will be issued.
This number is valid for fourteen (14) calendar days from the date of issue.
3.
After obtaining the R.A. number, return the approved equipment to your distributor, referencing the R.A. number. Your distributor will then replace the product over the counter at no charge. The
distributor will then return the product to Viking using the same R.A. number.
4. The distributor will NOT exchange this product without first obtaining the R.A. number from you. If you haven't followed the steps listed in 1, 2 and 3, be aware that you will have to pay a
restocking charge.
(+) Black
(-) Black with
White Stripe
Step 1.
Step 2.
Step 3.
IMPORTANT:
Do
NOT
plug in the
adapter until after
Step 3
is completed.
Step 1. Cut off the barrel connector.
Step 2. Seperate wires
Step 3. Connect 12V adapter wires to power
supply wires on LDB-3 Control Module
using supplied Butt Connectors and
then plug in power supply
Preparing the Power Supply
Connect power supply
wires to LDB-3 module
power supply wires
LIMITED WARRANTY
Viking warrants its products to be free from defects in the workmanship or materials, under normal use and service, for a period of one year from the date of purchase from any authorized Viking distributor or 18 months from the date manu-
factured, which ever is greater. If at any time during the warranty period, the product is deemed defective or malfunctions, return the product to Viking Electronics, Inc., 1531 Industrial Street, Hudson, WI., 54016. Customer must contact Viking's
Technical Support Department at 715-386-8666 to obtain a Return Authorization (R.A.) number.
This warranty does not cover any damage to the product due to lightning, over voltage, under voltage, accident, misuse, abuse, negligence or any damage caused by use of the product by the purchaser or others. This warranty does not cover
non-EWP products that have been exposed to wet or corrosive environments.
NO OTHER WARRANTIES. VIKING MAKES NO WARRANTIES RELATING TO ITS PRODUCTS OTHER THAN AS DESCRIBED ABOVE AND DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTIES OR MERCHANTABILITY OR FIT-
NESS FOR ANY PARTICULAR PURPOSE.
EXCLUSION OF CONSEQUENTIAL DAMAGES. VIKING SHALL NOT, UNDER ANY CIRCUMSTANCES, BE LIABLE TO PURCHASER, OR ANY OTHER PARTY, FOR CONSEQUENTIAL, INCIDENTAL, SPECIAL OR EXEMPLARY DAM-
AGES ARISING OUT OF OR RELATED TO THE SALE OR USE OF THE PRODUCT SOLD HEREUNDER.
EXCLUSIVE REMEDY AND LIMITATION OF LIABILITY. WHETHER IN AN ACTION BASED ON CONTRACT, TORT (INCLUDING NEGLIGENCE OR STRICT LIABILITY) OR ANY OTHER LEGAL THEORY, ANY LIABILITY OF VIKING SHALL
BE LIMITED TO REPAIR OR REPLACEMENT OF THE PRODUCT, OR AT VIKING'S OPTION, REFUND OF THE PURCHASE PRICE AS THE EXCLUSIVE REMEDY AND ANY LIABILITY OF VIKING SHALL BE SO LIMITED.
IT IS EXPRESSLY UNDERSTOOD AND AGREED THAT EACH AND EVERY PROVISION OF THIS AGREEMENT WHICH PROVIDES FOR DISCLAIMER OF WARRANTIES, EXCLUSION OF CONSEQUENTIAL DAMAGES, AND EXCLU-
SIVE REMEDY AND LIMITATION OF LIABILITY, ARE SEVERABLE FROM ANY OTHER PROVISION AND EACH PROVISION IS A SEPARABLE AND INDEPENDENT ELEMENT OF RISK ALLOCATION AND IS INTENDED TO BE ENFORCED
AS SUCH.
** Important:
First fully tighten the
nipple into the faceplate. Next add
the (2) nylon spacers, then fasten
the strobe mounting ring.
*** Note:
For outdoor applications,
orient the blue strobe light with the
screws at the top and bottom. Use a
bead of silicone to fill any gaps or
spaces to prevent water from enter-
ing the strobe light.
