manualshive.com logo in svg
background image

1

READ AND SAVE THESE INSTRUCTIONS

MODEL VEV1500
EXTERIOR MOUNTED BLOWER

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,
OR INJURY TO PERSONS, OBSERVE THE FOLLOW-
ING:

1. Use this unit only in the manner intended by the manu-

facturer. If you have questions, contact the manufac-
turer or your distributor.

2. Before servicing or cleaning unit, switch power off at

service panel and lock the service disconnecting means
to prevent power from being switched on accidentally.
When the service disconnecting means cannot be
locked, securely fasten a prominent warning device,
such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by

a qualified person(s) in accordance with all applicable
codes and standards, including fire-rated construction
codes and standards.

4. Sufficient air is needed for proper combustion and

exhausting of gases through the flue (chimney) of fuel
burning equipment to prevent backdrafting. Follow the
heating equipment manufacturer's guideline and safety
standards such as those published by the National Fire
Protection Association (NFPA), and the American So-
ciety for Heating, Refrigeration and Air Conditioning

CAUTION

1.

For general ventilating use only. Do not use to exhaust hazard-
ous or explosive material and vapors.

2.

To avoid motor bearing damage and noisy and/or unbalanced
impellers, keep drywall spray, construction dust, etc. off power
unit.

3.

Please read specification label on product for further informa-
tion and requirements.

4.

Electrical circuit, including speed control, (if used), must be
rated 6 AMPS minimum.

Blower Dimensions

25 x 30.828 x 12.724

PLAN THE
INSTALLATION

1. Locate the blower so the

length of the duct run and
number of elbows needed
are kept to a minimum.

2. Where possible, blower

should be centered be-
tween wall studs or roof
rafters.

3. Avoid pipes, wires, or

other ductwork that may
be running through the
wall.

ALL  INSTALLATIONS

MODEL

VOLTS

AMPS

CFM

DUCT SIZE

VEV1500

120

4.3

1500

10"  DIA.

SPECIFICATIONS

INSTALLER: Leave This Manual With The Homeowner

HOMEOWNER: Use And Care Information On Page 4

MODEL VEV1500

EXTERIOR BLOWER

WALL HOOD

CANOPY

(island canopy

available)

10" ROUND

DUCT

SOFFIT

ROUGH-IN

PLATE

24" or 27"

18"

MODEL

VEV1500

EXTERIOR

BLOWER

WALL HOOD

CANOPY

(island canopy

available)

10" ROUND DUCT

SOFFIT

ROUGH-IN

PLATE

24" or 27"

18"

10" ROUND ELBOW

TYPICAL ROOF MOUNTED INSTALLATION

TYPICAL WALL MOUNTED INSTALLATION

Engineers (ASHRAE), and the local code authorities.

5. When cutting or drilling into wall, or ceiling, do not

damage electrical wiring or other hidden utilities.

6. Ducted fans must always be vented to the outdoors.

7. To reduce risk of fire, use only metal ductwork.

8. This unit must be grounded.

WARNING

FOR USE ONLY WITH VIKING VWH/VBCV/V

I

H/V

I

CV/DTWN - 42”W (ISLAND

ONLY) - 66”W. WALL AND ISLAND HOODS.

Содержание VEV1500









Отзывы: