Vigorkiy rc hobby SUPER EXTRA330SC Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 23

background image

Install the rudder. Apply some glue on both sides of the wood piece, and install it as shown. Install this piece
with glue wet. Make sure that it is in alignment with the fuselage.

Once the wood piece for the rudder are dry, the rudder can be installed. Apply some glue and join the two
pieces. Make sure the rudder aligns with the wood pieces and that it is straight and true with the main part of
the fuselage.

«
...
16
17
18
19
20
...
»

Содержание SUPER EXTRA330SC
























Отзывы:

Нет отзывов

Похожие инструкции для SUPER EXTRA330SC

Бренд: Eduard Страницы: 3

Бренд: Fisher-Price Страницы: 10

Бренд: Align Страницы: 36

Бренд: Techone Страницы: 6

Бренд: Fisher-Price Страницы: 10

Бренд: MODSTER Страницы: 13

Бренд: Jamara Страницы: 12

Бренд: Trix Страницы: 28

Historic Wings Fokker Spin 1912

Бренд: Aircraft in Miniature Limited Страницы: 10

Бренд: Clas Ohlson Страницы: 5

Бренд: LeapFrog Страницы: 3

BEUREIHE 182 TAURUS

Бренд: marklin Страницы: 32

Бренд: East R/C Страницы: 23

Бренд: AE Страницы: 34

Бренд: SPAD Страницы: 11

Бренд: HobbyZone Страницы: 2

Top RAIDERS wave shark

Бренд: JUNIOR HOBBY Страницы: 13

Бренд: CopterX Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды