Vigorkiy rc hobby SUPER EXTRA330SC Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 23

background image

Push rods assembly
The push rod is made by connecting 1.5mm diameter carbon rod with Z-shaped steel wire instead of push
rod linkage stopper.
Fix the Z-shaped wire and the carbon rod with heat-shrink tubing. Make all of the control rods needed in the
same way.

Install aileron control rods.
Install the push rod linkage stopper, apply a dab of glue on the screw.

«
...
13
14
15
16
17
...
»

Содержание SUPER EXTRA330SC
























Отзывы:

Нет отзывов

Похожие инструкции для SUPER EXTRA330SC

Бренд: Zippkits Страницы: 26

Бренд: Gayla Страницы: 2

HMS NEW ZEALAND Battlecruiser 1912

Бренд: Combrig Страницы: 4

Бренд: Fisher-Price Страницы: 4

Alphabert s Pen Pal Phonics

Бренд: VTech Страницы: 16

Бренд: E-FLITE Страницы: 32

Бренд: MegaTech Страницы: 12

Education RENEWABLE ENERGY WATER POWERED...

Бренд: K'Nex Страницы: 20

Бренд: GREAT PLANES Страницы: 16

Бренд: Smoby Страницы: 4

SCOOBY-DOO 75901

Бренд: LEGO Страницы: 67

Wattage Thermalaire EP

Бренд: Academy of Model Aeronautics Страницы: 28

Бренд: Velleman Страницы: 9

Бренд: VBC Racing Страницы: 30

Tiger Moth DH82 2.15M

Бренд: Dancing Wings Hobby Страницы: 8

Bussing 8000 S13

Бренд: REVELL Страницы: 19

Бренд: Walkera Страницы: 10

Бренд: Beyblade Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды