VIETA VC-HA4000BT, Руководство пользователя

Страница: 13 / 28

13
When selecting a desired audio mode, rotate the VOL
knob to adjust the audio effect.
In each mode, the waiting time is about 5 seconds,
and the time waiting time is over, it returns to the last
display mode of tuner or CD mode.
The control mode of E.VOL is operated with following
numeric display.
- VOL: (MIN)0, ......45(MAX).
- BASS/TRE: -12, ......+12
- BAL: 10L, ...... 10R
- FAD: 10F,......10R
b) When pressed longer 2 seconds, it show the time
then it is activated as cyclical mode of following
functions for user s selection.
->INVOL ->CLK mode(you can adjust HOUR or
MINUTE by rotate the VOL knob) ->BEEP (ON/OFF)-
>TAVOL->REG ON/OFF-> AF(ON/OFF)->TA(ON/
OFF) -> ALARMON/OFF ->USER SET(FLAT/EQ OFF/
POP/ROCK/CLASSIC) ->LOUD(ON/OFF) ->LOC ON/
OFF(only for FM mode) ->MONO/STEREO(only for
FMmode) ->AREA(EUROPE/USA)
After selecting the desired mode, rotate the VOL
knob to select one setup item of the desired mode.
1) TA [TRAFFICANNOUNCEMENT]
When TA mode is on(TA is displayed on LCD), it
will begin to seek TA station and TA SEEK will be
displayed on LCD for a while.
When traffic announcement is transmitted:
(1) If the unit is in USB or disc mode, it will switch to
radio mode temporarily.
Temporarily switch over to an EON linked station
when EON detects a traffic announcement on that
other program, and TP will be displayed on LCD
(2 )If volume level is below 20, volume level is raised
to 20, and returns to its previous mode and volume
level when the traffic announcement is over.
(3) If volume is adjusted during traffic announcement,
only the traffic announcement volume is valid.
* TA interruption function:
The current traffic announcement is cancelled by
pressing this key. But the TA mode will not be off.
* When TA is on, SEEK, (SCAN), AUTO MEMORY
function can be received or saved only when traffic
programidentification code has been received.
2) AF [ALTERNATIVE FREQUENCIES]
When AF switching mode is selected and the state
of AF switching mode is displayed by AF segment in
display.
Segment off: AF switching mode off.
Segment on: AF switching mode on, and has RDS
information. Segment flashing: AF switching mode on, but RDS
information is not received yet.
When AF switching mode is selected, the radio
checks the signal strength of AF all the time. The
interval of checking time of each AFs depends on the
signal strength of current station, from a few minute
for strong station to a few seconds for weak station.
Every time that new AF is stronger than current
station, it switches over to that frequency for very
short time, and NEWFREQUENCY is displayed for 1-2
seconds. Because the mute time of AF switching or
checking time is very short, it is almost inaudible in
case of normal program.
During FMmode, when AF is on, SEEK, (SCAN),
AUTO-MEMORY function can only receive and save
RDS program.
3) TA SEEK/TAALARM:
TA SEEK mode: when newly tuned station does
not receive TP information for 5 seconds, the radio
retunes to next station which has a different PI to the
last station, but has the TP information.
When TP information gets lost at the current station
for retune time which is set by RETUNE SHORT(60
seconds) or RETUNE LONG(90 seconds), the radio
starts to retune to next same PI station. When same
PI station does not receive in 1 cyclic search, the
radio retunes to next station with TP information.
TA ALARMmode: when this mode is selected, any
automatic retune mode is not activated. Only double
beep sound(ALARM) will be heard.
When newly tuned station does not have TP
information for 5 seconds, beeps are sounded.
When TP information gets lost at the current station
for retune time, the beep sound will be heard.
When newly tuned station has no RDS signal, PI
SEEK is suppressed.
4) PI SOUND/ PI MUTE:
PI SOUND mode: if a car cruises between buildings
that could cause reflecting signals, a phenomenon
may occur, due to different PI codes being received
from the same AF source. when different PI sounds
(DIP) are heard occassionally, this will happen for
less than 1 second.
PI MUTE mode: under above same situation, a mute
sound will be heard for less than1second.
5) RETUNE L / RETUNE S:
The initial time of automatic TAsearch or PI SEARCH
mode is selected.
When PI information is not received for retune
interval, the radio starts to retune to next same PI
station.
When same PI station does not receive 1 cyclic
search, the radio goes to last station and waits for 4-5
minutes until PI code is received.