manualshive.com logo in svg

Viessmann CM2C, Инструкция по установке для подрядчиков

Поделиться
Скачать
Viessmann CM2C Скачать руководство пользователя страница 25

25

1. 

Make the safety connections.
Install all pipe connections free of load and torque
stress.

2. 

Check the connections on the heating water side
for leaks.

Permiss. operating pres-
sure

6 bar (0.6 MPa)

Test pressure

7.8 bar (0.78 MPa)

Low water indicator (water level limiter)

Protect the boilers against water shortage in accord-
ance with EN 12828. A minimum pressure switch or
minimum pressure limiter can be installed for this,
available as accessories.

Safety valve

Equip boilers with a safety valve that is individually tes-
ted to EN 12828 and is marked according to the sys-
tem version.

Connecting the control unit

Connections to the electronics unit

Boiler control unit installation instructions

Note

Route 230 V cables and LV leads separately.

!

Please note

Hot components can damage electrical cables.
Never allow cables/leads to come into contact
with hot components. Secure all cables/leads
with cable ties.

 

Making the safety connections

5799212

 

Содержание CM2C

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды