Vidikron Vision 140 Скачать руководство пользователя страница 98

Страница: 98 / 116

Maintenance and Troubleshooting

Vision Model 140/150 Installation/Operation Manual

PRE

IMINAR

5.2
Lens Replacement

If you need to remove the lens – either to replace it or to prepare the projector for shipment –
proceed as follows:

Power down the projector and wait five minutes to allow the lamp to cool.

Remove the secondary anamorphic lens, if present.

Place the lens cap on the installed lens to protect it from damage.

Press and hold the “lens release” button located in the top right corner of the lens panel.

Grasping the lens barrel, turn it in a counter-clockwise direction until it stops. Then, pull
it forward to remove it (disconnects from the connector assembly).

Figure 5-6. Removing the Primary Lens

Note: The connector assembly moves as you turn the lens.

Содержание Vision 140





















































































































Результаты поиска

Содержание Vision 140

Отзывы:

Похожие инструкции для Vision 140

Бренды по названию

Популярные бренды

Vidikron Vision 140, Руководство по установке и эксплуатации

Результаты поиска

Содержание Vision 140

Отзывы:

Похожие инструкции для Vision 140

Бренды по названию

Популярные бренды