Videx GSMVRK Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 60

Videx GSMVRK Скачать руководство пользователя страница 7

66250675-EN - V1.0 - 05/09/17

7

4000 Series Vandal Resistant GSM Audio Intercom with Proximity Facility

4000 Series Vandal Resistant GSM - Technical Manual

BUTTON HARNESS WIRING

6

a

b

c

d

5

1

2

3

4

8

7

6

5

4

3

2

1

12

11

10

9

16

15

14

13

20

19

18

17

24

23

22

21

white wire

red wire

brown wire

black wire

grey wire

yellow wire

violet wire

blue wire

green wire

orange wire

button harness connector

Fig. 3

BUTTON MODULE NOTES

If the GSM module has 1 button (VR4KGSM-1), the additional button module buttons should be wired starting from button number
2 (i.e. the first button of the button module should be connected using the green “b” and white “1” wires, the next button using the
blue “c” and white “1” wires etc.).

If the GSM module has 2 buttons (VR4KGSM-2), the additional button module buttons should be wired starting from button number
3 (i.e. the first button of the button module should be connected using the blue “c” and white “1” wires, the next button using the
violet “d” and white “1” wires etc.).

If the GSM module has 3 buttons (VR4KGSM-3), the additional button module buttons should be wired starting from button number
4 (i.e. the first button of the button module should be connected using the violet “d” and white “1” wires, the next button using the
orange “a” and pink “2” wires etc.).

The button harness table below can also be used to determine the required button module wiring.

Button No.

Harness Connector Pins

Wire Colours

Button No.

Harness Connector Pins

Wire Colours

1

a - 1

orange / white

13

a - 4

orange / black

2

b - 1

green / white

14

b - 4

green / black

3

c - 1

blue / white

15

c - 4

blue / black

4

d - 1

violet / white

16

d - 4

violet / black

5

a - 2

orange / red

17

a - 5

orange / grey

6

b - 2

green / red

18

b - 5

green / grey

7

c - 2

blue / red

19

c - 5

blue / grey

8

d - 2

violet / red

20

d - 5

violet / grey

9

a - 3

orange / brown

21

a - 6

orange / yellow

10

b - 3

green / brown

22

b - 6

green / yellow

11

c - 3

blue / brown

23

c - 6

blue / yellow

12

d - 3

violet / brown

24

d - 6

violet / yellow

System Components and Available Versions

«
...
5
6
7
8
9
...
»

Содержание GSMVRK





























































Отзывы:

Нет отзывов