manualshive.com logo in svg

Victron energy Blue Power BMV-602, Руководство пользователя

Поделиться
Скачать
Victron energy Blue Power BMV-602 Скачать руководство пользователя страница 17

13 

www.victronenergy.co

m 

Rlc:

 

Clear relay low voltage.

 When the battery voltage rises above this 

value, the alarm relay will be de-activated. This value needs to be 
greater than or equal to Rl. 

Rh:

 

Relay high voltage.

 When the battery voltage rises above this 

value for more than 10 seconds the alarm relay will be activated. 

Rhc:

 

Clear relay high voltage.

 When the battery voltage falls below this 

value, the alarm relay will be de-activated. This value needs to be 
less than or equal to Rh. 

BLI:

 

Intensity backlight.

 The intensity of the backlight, ranging from 0 

(always off) to 9 (maximum intensity). 

D V:

 

Battery voltage display.

 Determines if the battery voltage is 

available in the monitoring menu. 

D I:

 

Current display.

 Determines if the current is available in the 

monitoring menu. 

D CE:

 

Consumed energy display.

 Determines if the consumed energy 

is available in the monitoring menu. 

D SOC:

 

State-of-charge display.

 Determines if the state of charge is 

available in the monitoring menu. 

D TTG:

 

Time-to-go display.

 Determines if the time to go is available in 

the monitoring menu. 

ZERO:

 

Zero current calibration.

 If the BMV reads a non-zero current 

even when there is no load and the battery is not charging, this 
option can be used to calibrate the zero reading. Ensure that there 
really is no current flowing into or out of the battery, then hold the 
select button for 5 seconds. 

SYNC:

 

Manual synchronization.

 This option can be used to manually 

synchronize the BMV. When the battery is fully charged, hold the 
select button for 5 seconds. Note: If the BMV fails to automatically 
synchronize, check the wiring, and ensure that Cb, Vc, It, and Tcd 
are set correctly. 

R DEF:

 

Reset to factory defaults.

 Reset all settings to the factory 

defaults by holding the select button for 5 seconds. 

Cl HIS:

 

Clear historic data.

 Clear all historical data by holding the select 

button for 5 seconds. 

Lock:

 

Setup lock.

 When on, all settings (except this one) are locked and 

cannot be altered. 

SW:

 

Firmware version

 (cannot be altered). 

Содержание Blue Power BMV-602

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды