Victaulic VicFlex AH1 Скачать руководство пользователя страница 237

Страница: 237 / 239

TFP181

Page 2 of 4

Adjustment

1/2 inch (12,7 mm)

Finishes

See the Ordering Procedure section.

Physical Characteristics

Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . .Bronze

Support Cup . . . . . . . . . . . .Chrome Plated Steel

Guide Pins . . . . . . . . . . . . . . . . . . Stainless Steel

Deflector . . . . . . . . . . . . . . . . . . . . . . . . . .Bronze

Compression Screw . . . . . . . . . . . . . . . . . .Brass

Bulb

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Glass

Cap . . . . . . . . . . . . . . . . . . . . . Bronze or Copper

Sealing Assembly . .Beryllium Nickel w/TEFLON

Cover Plate . . . . . . . . . . . . . . . . . . . . . . . . .Brass

Retainer . . . . . . . . . . . . . . . . . . . . . . . . . . . .Brass

Ejection Spring . . . . . . . . . . . . . . Stainless Steel

Design

Criteria

The TYCO Series RFII 5.6 K-factor,

“Royal Flush II” Concealed Pendent

Sprinklers are intended for fire protec-

tion systems designed in accordance

with the standard installation rules

recognized by the applicable Listing

or Approval agency; for example, UL

Listing is based on NFPA 13 and VdS

Approval is based on the CEA 4001.
For more information on LPCB and VdS

Approvals, contact Tyco Fire Protection

Products at the following office:

Enschede, Netherlands

Telephone: 31-53-428-4444

Fax: 31-53-428-3377

The Series RFII Concealed Pendent

Sprinklers are only listed and approved

with the Series RFII Concealed Cover

Plates having a factory applied finish.

NOTICE

Do not use the Series RFII in applica-

tions where the air pressure above the

ceiling is greater than that below. Down

drafts through the Sprinkler/Support

Cup Assembly can delay sprinkler

operation in a fire situation.

Operation

When exposed to heat from a fire, the

Cover Plate, normally soldered to the

Retainer at three points, falls away to

expose the Sprinkler/Support Cup

Assembly.
The Deflector — supported by the

Guide Pins — then drops down to its

operational position.
The glass bulb contains a fluid that

expands when exposed to heat. When

the rated temperature is reached, the

fluid expands sufficiently to shatter the

glass bulb, activating the sprinkler and

allowing water to flow.

Installation

The TYCO Series RFII 5.6 K-factor,

“Royal Flush II” Concealed Pendent

Sprinklers must be installed in accor-

dance with this section.

General Instructions

Do not install any bulb-type sprinkler

if the bulb is cracked or there is a loss

of liquid from the bulb. With the sprin-

kler held horizontally, a small air bubble

should be present. The diameter of the

air bubble is approximately 1/16 inch

(1,6 mm) for the 155°F (68°C) and 3/32

inch (2,4 mm) for the 200°F (93°C) tem-

perature ratings.
A leak-tight 1/2 inch NPT sprinkler

joint should be obtained by applying a

minimum to maximum torque of 7 to 14

ft.-lbs. (9,5 to 19,0 Nm). Higher levels

of torque can distort the sprinkler Inlet

with consequent leakage or impairment

of the sprinkler.

Do not attempt to compensate for

insufficient adjustment in the Sprinkler

by under- or over-tightening the Sprin-

kler/Support Cup Assembly. Re-adjust

the position of the sprinkler fitting to

suit.

Step 1.

Install the sprinkler only in the

pendent position with the center-line

of the sprinkler perpendicular to the

mounting surface.

Step 2.

Remove the Protective Cap.

Step 3.

With pipe thread sealant

applied to the pipe threads, hand-

tighten the sprinkler into the sprinkler

fitting.

Step 4.

Wrench-tighten the sprinkler

using only the RFII Sprinkler Wrench.

(Refer to Figure 3.) Apply the RFII

Sprinkler Wrench to the Sprinkler as

shown in Figure 3.

SPRINKLER/SUPPORT CUP

ASSEMBLY

COVER PLATE/RETAINER

ASSEMBLY

GUIDE

PINS (2)

DEFLECTOR

(DROPPED

POSITION)

COMPRESSION

SCREW

DEFLECTOR

SUPPORT

CUP WITH

ROLL FORMED

THREADS

FRAME

1/2" NPT

CAP

BULB

SEALING

ASSEMBLY

RETAINER

WITH THREAD

DIMPLES

EJECTION

SPRING

SOLDER

TABS (3)

COVER

PLATE

THREAD INTO

SUPPORT

CUP UNTIL

MOUNTING

SURFACE IS

FLUSH WITH

CEILING

FIGURE 1

MODEL RFII CONCEALED SPRINKLER

ASSEMBLY

Содержание VicFlex AH1
















































































































































































































































Результаты поиска

Содержание VicFlex AH1

Отзывы:

Похожие инструкции для VicFlex AH1

Бренды по названию

Популярные бренды

Victaulic VicFlex AH1, Руководство пользователя

Результаты поиска

Содержание VicFlex AH1

Отзывы:

Похожие инструкции для VicFlex AH1

Бренды по названию

Популярные бренды