Victaulic VicFlex AH1 Скачать руководство пользователя страница 176

Страница: 176 / 239

TFP181

Page 3 of 4

A: 3-1/4 inches (82,6 mm)

C: 2-3/8 to 2-5/8 inches (60,3 to 66,7 mm)

B: 3/16 inches (4,8 mm)

D: 1-3/4 to 2-1/4 inches (44,5 to 57,2 mm)

Step 5.

Replace the Protective Cap

by pushing it upwards until it bottoms

out against the Support Cup. (Refer

to Figure 4.) The Protective Cap helps

prevent damage to the Deflector and

Arms during ceiling installation and/or

finish. You can also use the Protective

Cap to locate the center of the clear-

ance hole by gently pushing the ceiling

material up against the center point of

the Protective Cap.

NOTICE

As long as the Protective Cap remains

in place, the system is considered “Out

of Service”.

Step 6.

After the ceiling has been

completed with the 2-1/2 inch (63,5

mm) diameter clearance hole and in

preparation for installing the Cover

Plate/Retainer Assembly, remove and

discard the Protective Cap. Verify that

the Deflector moves up and down

freely.
If the Sprinkler is damaged and the

Deflector does not move up and down

freely, replace the entire Sprinkler.

Do not attempt to modify or repair a

damaged sprinkler.

Step 7.

When installing an Air and

Dust Seal, refer to Figure 5; otherwise,

proceed to Step 8. To attach the Air

and Dust Seal, verify the angle of the

outside edge of the seal is oriented

according to Figure 5. Start the edge of

the Retainer in the grooved slot of the

Air and Dust Seal and continue around

the retainer until the entire Air and Dust

Seal is engaged.

COVER PLATE

PROFILE DEPTH

DIMENSION B

1/2" (12,7 mm)

THREADED

ADJUSTMENT

FACE OF

SPRINKLER

FITTING

MANUFACTURER

PRESET GAP

3/32" (2,4 mm)

FACE

OF CEILING,

RETAINING RING

MOUNTING

SURFACE

SPRINKLER

SUPPORT CUP

ASSEMBLY

CLEARANCE HOLE

DIAMETER

DIMENSION C

DEFLECTOR

IN DROPPED

POSITION

3/16" to 11/16"

(4,8 to 17,5 mm)

REFERENCE

COVER PLATE

RETAINER

ASSEMBLY

COVER PLATE

DIAMETER

DIMENSION A

CLEARANCE

HOLE

FRAME

ARM

SUPPORT

CUP

7/8" (23 mm)

SQUARE

ACCEPTS

1/2" SOCKET

DRIVE

ALIGN

ARROWS WITH

FRAME ARMS

FIGURE 2

SERIES CONCEALED SPRINKLER INSTALLATION DIMENSIONS

FIGURE 4

DISPOSABLE PROTECTIVE CAP

FIGURE 3

RFII SPRINKLER WRENCH

Содержание VicFlex AH1
















































































































































































































































Результаты поиска

Содержание VicFlex AH1

Отзывы:

Похожие инструкции для VicFlex AH1

Бренды по названию

Популярные бренды

Victaulic VicFlex AH1, Руководство пользователя

Результаты поиска

Содержание VicFlex AH1

Отзывы:

Похожие инструкции для VicFlex AH1

Бренды по названию

Популярные бренды