Victaulic TM-RG3212 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 28

Victaulic TM-RG3212 Скачать руководство пользователя страница 6

INTRODUCTION

NOTICE

• Drawings and/or pictures in this manual

may be exaggerated for clarity.

• The tool, along with this operating

and maintenance instructions manual,
contains trademarks, copyrights, and/or
patented features that are the exclusive
property of Victaulic.

The RG3212 is a hydraulic-feed shop or field
tool designed to roll groove carbon steel pipe or
stainless steel pipe of various diameters and wall
thicknesses . The RG3212 is a self-contained
unit with a motor, power cord/plug, and
hydraulic pump handle .

CAUTION

• The RG3212 should only be used for roll

grooving pipe designated in the “Tool
Ratings for Steel Pipe” section of this
manual.

Use of the tools for other purposes, or use
exceeding the pipe thickness maximums,
will overload the tools, shortening tool life
and potentially causing tool damage.

RECEIVING THE TOOL

RG3212 tools are packed individually in sturdy
containers that are designed for repeated
shipping . Save the container for return shipment
of rental tools .
Upon receipt of the tool, ensure that all
necessary parts are included . If any parts
are missing, contact Victaulic .

CONTAINER CONTENTS

Qty.

Description

1

Tool with Motor and Hydraulic Pump Handle

1

Foot Switch

1

PS3212 Pipe Stand

1

Roll Set for 2–3.5-inch Pipe -

Original Groove System Specification

1

Roll Set for 4–6-inch Pipe -

Original Groove System Specification

1

Roll Set for 8–12-inch Pipe -

Original Groove System Specification

1

Lower Roll Removal Wedge

1

Go/No-Go Grooved Pipe Diameter Tape

1

Storage Bag with Accessories

2

Operating and Maintenance Instructions Manual

6

REV_A

TM-RG3212

/ Operating and Maintenance Instructions Manual

«
...
4
5
6
7
8
...
»

Содержание TM-RG3212





























Отзывы:

Нет отзывов