manualshive.com logo in svg

Victaulic PFT505, Инструкция по эксплуатации и техническому обслуживанию, Страница: 6 / 12

Поделиться
Скачать
Victaulic PFT505 Скачать руководство пользователя страница 6

 

6

 

PFT505

 

TOOL NOMENCLATURE

 

NOTICE

 

Label (as pictured above) not shown at full scale. DO NOT
use this representation as a gauge or template to mark pipe.

Motor

Grip

Trigger

Power Cord

Jaw Lever

Pinch Point

Pinch Point

Locking Pin

Press
Jaw

Support
Neck

➀

➁

1. Always mark pipe using a Pressfit Pipe 
    Marking Gauge or per the chart below.

2. Always fully insert pipe into fitting.

3. Always properly position fitting in press
    jaw before pressing.

4. Never use pipe shorter than the minimum 
    lengths in the chart below.

Failure to do so can result in serious injury, improper assembly, joint  
leakage or joint failure, and property damage.

SIZE

¹⁄₂

"

³⁄₄

 

& 1"

1

¹⁄₄

"

1

¹⁄₂

"

2"

NOTE:

  

Line lengths shown above are actual sizes for use as a reference

             when marking pipe ends.

11/97      0629 Rev.A

INSERTION DEPTH

1 inch

⁷⁄₈

" inch

1

¹⁄₂

 inch

1

⁷⁄₈

 inch

1

¹⁄₄

 inch

MINIMUM PIPE NIPPLE

LENGTH REQUIRED

2

⁵⁄₈

"

2

⁷⁄₈

"

3

¹⁄₄

"

3

¹⁄₂

"

5"

R008500LAB

• Before installing Pressfit products, operating or servicing the 
  Pressfit Tool, read the Product Assembly and Tool Operation
  Manual and all warning labels on the tool and tool box.

• Only connect tool to a grounded electrical source, 20 amp
  maximum.

•  Always disconnect power before changing press jaws or 
   servicing.

•  Always wear safety glasses and foot protection.

•  Keep fingers and hands away from pressing jaws when
   pressing.

•  (1) Always mark the pipe. (2) Always fully insert pipe into the 
   fitting. (3) Always properly position fitting in press jaw before
   pressing.

Failure to follow these precautions can result in serious
injury, improper assembly, joint leakage or joint failure
and property damage.

R010500LAB

0631 Rev. C

➀

➁

 

TM-PFT505.1005 Rev.B  Page 6  Tuesday, May 29, 2001  6:01 PM

Содержание PFT505













Отзывы:

Нет отзывов