Victaulic PFT505 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 12

Victaulic PFT505 Скачать руководство пользователя страница 2

2

PFT505

Read this first – Hazard Identification

Definitions for identifying the various hazard levels shown on warning labels or to indicate proper

safety procedures in this Manual are provided below.

This safety alert symbol indicates important safety messages on warning labels and in

this manual. When you see this symbol be alert to the possibility of personal injury and

carefully read and fully understand the message that follows.

The use of the word “DANGER” signifies an immediate
hazard with a likelihood of serious personal injury or
death if instructions, including recommended
precautions, are not followed.

The use of the word “WARNING” signifies the
presence of hazards or unsafe practices which could
result in serious personal injury or death if
instructions, including recommended precautions, are
not followed.

The use of the word “CAUTION” signifies possible
hazards or unsafe practices which could result in
personal injury, product or property damage if
instructions, including precautions, are not followed.

NOTICE

The use of the word “NOTICE” signifies special
instructions which are important but not related to
hazards.

INDEX

Hazard Identification . . . . . . . . . . . . . . . . . . . . . 2

Operator Safety Instructions. . . . . . . . . . . . . . . 3

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Tool Set-Up . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Operating Tool . . . . . . . . . . . . . . . . . . . . . . . 3
Tool Maintenance . . . . . . . . . . . . . . . . . . . . . 4

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Power Requirements . . . . . . . . . . . . . . . . . . 5
Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Extension Cord Requirements . . . . . . . . . . 5

Tool Nomenclature. . . . . . . . . . . . . . . . . . . . . . . 6

Receiving Tool . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Tool Set-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Press Jaw Installation and Removal

Press Jaw Installation . . . . . . . . . . . . . . . 7

Press Jaw Removal . . . . . . . . . . . . . . . . . 8

Pressing Operation . . . . . . . . . . . . . . . . . . . . . . 8

Maintenance Procedures . . . . . . . . . . . . . . . . 10

Cleaning and Lubrication . . . . . . . . . . . . . 10

Press Jaws . . . . . . . . . . . . . . . . . . . . . . . 10

Roller Drive and Locking Pin . . . . . . . . 10

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . 11

TM-PFT505.1005 Rev.B Page 2 Tuesday, May 29, 2001 6:01 PM

«
1
2
3
4
...
»

Содержание PFT505













Отзывы:

Нет отзывов