background image

The Power Behind Performance

Rev 1.1    3/13   

vicorpower.com  

Applications Engineering: 800 927.9474       

 Page 21

Vicor’s comprehensive line of power solutions includes high density AC-DC and DC-DC modules and  
accessory components, fully configurable AC-DC and DC-DC power supplies, and complete custom power 
systems. 

Information furnished by Vicor is believed to be accurate and reliable. However, no responsibility is assumed by 

Vicor for its use. Vicor makes no representations or warranties with respect to the accuracy or completeness of the 

contents of this publication. Vicor reserves the right to make changes to any products, specifications, and product 

descriptions at any time without notice. Information published by Vicor has been checked and is believed to be 

accurate at the time it was printed; however, Vicor assumes no responsibility for inaccuracies. Testing and other 

quality controls are used to the extent Vicor deems necessary to support Vicor’s product warranty. Except where 

mandated by government requirements, testing of all parameters of each product is not necessarily performed. 

Specifications are subject to change without notice.

Vicor’s Standard Terms and Conditions

All sales are subject to Vicor’s Standard Terms and Conditions of Sale, which are available on Vicor’s webpage or 

upon request.

Product Warranty

In Vicor’s standard terms and conditions of sale, Vicor warrants that its products are free from non-conformity to 

its Standard Specifications (the “Express Limited Warranty”). This warranty is extended only to the original Buyer 

for the period expiring two (2) years after the date of shipment and is not transferable. 

UNLESS OTHERWISE EXPRESSLY STATED IN A WRITTEN SALES AGREEMENT SIGNED BY A DULY  
AUTHORIZED VICOR SIGNATORY, VICOR DISCLAIMS ALL REPRESENTATIONS, LIABILITIES, AND  
WARRANTIES OF ANY KIND (WHETHER ARISING BY IMPLICATION OR BY OPERATION OF LAW) WITH  
RESPECT TO THE PRODUCTS, INCLUDING, WITHOUT LIMITATION, ANY WARRANTIES OR REPRESENTATIONS 
AS TO MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE, INFRINGEMENT OF ANY PATENT,  
COPYRIGHT, OR OTHER INTELLECTUAL PROPERTY RIGHT, OR ANY OTHER MATTER. 

This warranty does not extend to products subjected to misuse, accident, or improper application, maintenance, 

or storage. Vicor shall not be liable for collateral or consequential damage. Vicor disclaims any and all liability 

arising out of the application or use of any product or circuit and assumes no liability for applications assistance 

or buyer product design. Buyers are responsible for their products and applications using Vicor products and 

components. Prior to using or distributing any products that include Vicor components, buyers should provide 

adequate design, testing and operating safeguards.

Vicor will repair or replace defective products in accordance with its own best judgment. For service under this 

warranty, the buyer must contact Vicor to obtain a Return Material Authorization (RMA) number and shipping 

instructions. Products returned without prior authorization will be returned to the buyer. The buyer will pay all 

charges incurred in returning the product to the factory. Vicor will pay all reshipment charges if the product was 

defective within the terms of this warranty.

Life Support Policy

VICOR’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DE-
VICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE  
OFFICER AND GENERAL COUNSEL OF VICOR CORPORATION.

  As used herein, life support devices or systems 

are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose 

failure to perform when properly used in accordance with instructions for use provided in the labeling can be 

reasonably expected to result in a significant injury to the user. A critical component is any component in a life 

support device or system whose failure to perform can be reasonably expected to cause the failure of the life 

support device or system or to affect its safety or effectiveness. Per Vicor Terms and Conditions of Sale, the user of 

Vicor products and components in life support applications assumes all risks of such use and indemnifies Vicor 

against all liability and damages.

Intellectual Property Notice

Vicor and its subsidiaries own Intellectual Property (including issued U.S. and Foreign Patents and pending patent 

applications) relating to the products described in this data sheet. No license, whether express, implied, or  

arising by estoppel or otherwise, to any intellectual property rights is granted by this document.  Interested  

parties should contact Vicor's Intellectual Property Department.

Vicor Corporation

25 Frontage Road
Andover, MA, USA 01810
Tel: 800-735-6200
Fax: 978-475-6715

Email

Customer Service: 

[email protected]

Technical Support: 

[email protected]

Содержание MicroPAC






















Отзывы: