background image

Item Quantity 

Function 

Rubber grommet 

Seals cable access hole against dust, 
prevents cable abrasion 

No. 8 Torx™ bit 

Use to remove and install tamperproof 
screws 

No. 8-32 tamperproof Torx screw 

Supplied as spares 

Cable tie mount, adhesive base  

Secures camera power cables 

Cable tie 

Secures camera power cables 

Table 2: Accessory Pack Contents

 

 

Required tool:

 The Torx bit that is supplied is designed for a socket or screwdriver-type holder designed for 

hexagonal bits. 

Mounting the Housing 

The housing consists of two main assemblies, the outer or front cover and the back corner or wall mount 
assembly. The front of the housing is secured to the back of the housing with Torx tamperproof screws. A 
special tool is supplied in the accessory pack for removing and replacing these screws. When the installation 
is complete, retain the Torx bit in case access to the interior of the housing is required later. Two extra Torx 
screws are provided in the accessory pack  
 

Note:

 The camera mounting bracket assembly can be removed if desired. Loosen the self-locking nut and 

disconnect the cable at the camera PCB. 

 
There are four (4) 0.22-inch (5.6-mm) holes that are provided for mounting the housing assembly to the wall 
and/or ceiling to assure a secure mounting. A 0.750-inch (19-mm) hole is provided for cable access. 

1.  Remove the front cover. Using the housing back as a template, mark the location of the cable access 

opening in the wall or ceiling and the locations of the mounting screws. 

2.  Cut the cable opening in the wall. The cable opening diameter should be slightly larger than the outer 

diameter of the rubber grommet from the accessory pack. This allows the housing to fit flush against the 
wall when installed. Optionally, a conduit fitting (not supplied) can be used. 

3.  Drill suitable holes for whatever type of hollow-wall hardware has been selected. The use of No. 10 

hardware is recommended. Use hollow-wall anchors or, if the housing is being mounted on a sheet metal 
surface, use rivet nuts. 

4.  The cable access hole in the housing accommodates standard cable access fittings as used with 

electrical junction boxes. If such a fitting is not to be used, install the rubber grommet from the accessory 
pack. The grommet has been split for preterminated coaxial cable. The grommet protects video and 
power cables from abrasion and prevents dust from entering the housing through the cable access hole. 

5.  Pull enough power cable and coaxial cable through the grommet into the housing to allow for convenient 

handling during termination. 

6.  Fasten the housing to the wall with four fasteners appropriate for the mounting surface. 

4  

  Installation 

X935-20-00  Rev 1204 V894CSHR-VF/V894WSHR-VF High-Security Cameras 

Содержание Roughneck V894CSHR-VF-C























Отзывы: