Vicon Pilot Lite V1522 Скачать руководство пользователя

Страница: 101 / 138

Creating a Configuration

3-61

Pilot Lite

XX196-00

All selections are made using the Options Wizard. To change a field’s value,
proceed as follows:

1. Select the field that you wish to modify using the Available Field

selection box. You can scroll through all available options.

2. Upon selection, the title below Available Field will change to the

parameter selected and the appropriate values will display in the
selection box.

3. Select All for all, Selected Only for an item that is highlighted in the

list or From to specify a range.

4. Click Update to implement the changes.

Note:

The Settings box contains two buttons: Apply and Restore. Clicking

Apply will make the changes permanent. Clicking Restore will cancel the
changes that you have made and revert back to the original values. Once
you click Apply, you cannot restore the original values.

Содержание Pilot Lite V1522











































































































































Результаты поиска

Содержание Pilot Lite V1522

Отзывы:

Похожие инструкции для Pilot Lite V1522

Бренды по названию

Популярные бренды

Vicon Pilot Lite V1522, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Pilot Lite V1522

Отзывы:

Похожие инструкции для Pilot Lite V1522

Бренды по названию

Популярные бренды