manualshive.com logo in svg

Vicon Extra 532, Руководство по обслуживанию, Страница: 79 / 90

Поделиться
Скачать
Vicon Extra 532 Скачать руководство пользователя страница 79

Bevel gear changing oil

Bevel gear changing oil

Bevel gear changing oil

Bevel gear changing oil

Bevel gear changing oil

Bevel gear changing oil

After the first 50 hrs. thereafter 
every 200 hours or once a year.

Remove the oil plug.

•

Let the oil flow into a suitable 
container.

•

Allow the last of the oil to drip 
out of the transmission for 
approx.10 - 15 minutes.

•

Fit the oil plug.

•

Oil amount when changing oil:

•

Remove the dipstick.

•

Pour the oil through the hole 
where the dipstick is fitted.

•

Follow the instructions on the 
machine.

•

Check that the oil level is up 
to the “max” indication on the 
dipstick.

•

Repeat the procedure until the 
correct oil level is reached.

•

Fit the dipstick and fasten it

For gearboxes always use  
SAE GL5 EPX 80W-90

.

•

Decal with all information's 
what you can find on the 
machine.

4.9 Oil change gearboxes

79

Содержание Extra 532



























































































Отзывы:

Нет отзывов