manualshive.com logo in svg

Vicon Extra 532, Руководство по обслуживанию, Страница: 70 / 90

Поделиться
Скачать
Vicon Extra 532 Скачать руководство пользователя страница 70

Cutter bar repair

Assembly of intermediate 
gearwheel 

Cutter bar repair

Assembly of intermediate 
gearwheel 

Cutter bar repair

Change of bearing 
intermediate gearwheel 

Cutter bar repair

Change of bearing 
intermediate gearwheel 

•

Place tool T1 on top of the 
bearing as shown.

•

Force the bearing in place by 
use of a hammer as shown.

NB! 

The bearing must at all 

times being forced by the tool on 
the outer ring of the bearing 
when it is placed in the bearing 
house.

•

Guide the gear wheel trough 
the gap in the cutter bar.

•

Make sure the bearing is 
locked and fixed by the circlip.

NB! 

Force the bearing backward

and forward a bit to check the
bearing is locked and fixed in the
gear wheel.

•

Fit new O-rings on the shafts 
and into the hole for the 
shafts.

•

Fit the intermediate gear 
wheel..

•

Place and carefully force the 
shafts through the gear 
wheels.

NB! 

Make sure the gear wheels 

is placed just under the hole for 
the shafts in the cutter bar when 
fitted.

4.8.1 Cutter bar-repair instructions

70

Содержание Extra 532



























































































Отзывы:

Нет отзывов