manualshive.com logo in svg

Vicon Extra 532, Руководство по обслуживанию, Страница: 18 / 90

Поделиться
Скачать
Vicon Extra 532 Скачать руководство пользователя страница 18

Bleeding of the clutch.

Bleeding of the clutch

Bleeding of the clutch.

Bleeding of the clutch

Bleeding of the clutch.

Bleeding of the clutch.

The friction clutch is bled in the 
following way:

•

Open the guard and remove 
the PTO shaft with the friction 
clutch.

•

Tighten all bolts on the friction 
clutch.

•

Fit and fasten the friction 
clutch on the machine.

•

Block the cutter bar by placing 
a wooden block between the 
two cutting discs.

•

Start the tractor and connect 
the tractor's PTO outlet.

•

Let the friction clutch rotate 
freely for approx. 5 seconds at 
the lowest possible speed, 
until it is warm to the touch. 
Do not allow the friction clutch 
to rotate for more than approx. 
5 seconds at a time, as this 
may damage the friction discs. 

•

Disconnect the PTO outlet 
and stop the tractor. 

•

Remove the friction clutch 
from the machine. 

•

Loosen all the bolts on the 
friction clutch.

•

Fit and fasten the friction 
clutch on the machine.

•

Remove the wooden block 
from the cutter bar. 

2.3 Bleeding of slip clutch

18

Содержание Extra 532



























































































Отзывы:

Нет отзывов