VIASYS Bear Cub 750PSV Скачать руководство пользователя страница 73 | Manualshive

Страница: 73 / 98

VIASYS Bear Cub 750PSV Скачать руководство пользователя страница 73

Service Manual

73

Chapter 7 Removal & Replacement

WARNINGS

•

Disconnect all electrical power, air, and oxygen sources before attempting
any disassembly. Failure to do so could result in injury to the service
technician or damage to equipment.

•

After replacement of any assembly(ies), always repeat the Operational
Verification Procedure (refer to chapter 3), then allow a "burn-in" period and
repeat the Operational Verification Procedure.

Interior Access

1.

If connected, remove cables leading to RS-232 and Analog outputs ports of the
ventilator.

2.

Remove the seven screws indicated in Figure 7-1.

Figure 7-1: Cover Removal

3.

Slide the cover off of the unit applying slight pressure to the outside bottom
portion of the cover.

4.

Remove the two screws indicated in Figure 7-2. The standoff tubes will drop
free when the screws are removed.

NOTE

The front portion will swing forward freely when the screws are removed. Take care
to ensure that the front swings slowly to avoid damage to the unit.

L2346

Revision B

June 2004

«
...
71
72
73
74
75
...
»

Содержание Bear Cub 750PSV



































































































Отзывы:

Нет отзывов