manualshive.com logo in svg

VIASYS Bear Cub 750PSV, Руководство по обслуживанию, Страница: 25 / 98

Поделиться
Скачать
VIASYS Bear Cub 750PSV Скачать руководство пользователя страница 25

Service Manual 

 

25 

 

Ventilator pneumatics - General description 

Figure 2-2 shows the schematic diagram of the BEAR CUB™ 750PSV Pneumatics 
System.  The pneumatics interface to the electronics is achieved using various 
actuators (solenoids) and transducers.  The Pneumatics System consists of eight (8) 
main subsystems:  Gas Inlet and Conditioning, Oxygen Blender System, Flow 
Control, Sub-Ambient/Overpressure Relief system, Exhalation Valve/Pressure 
Control, Pressure Monitoring, the Proximal Airway Purge System, and the Auxiliary 
Gas Outlet. 

 

Gas Inlet Conditioning 

Compressed air and oxygen sources, supplied in the pressure range of 30 to 80 
psig, are connected to the standard DISS male-threaded fittings on the back panel of 
the ventilator. 

Incoming air passes through a coalescing filter housed in the Air Inlet Water Trap.  
Particulate matter down to .3 micron in size, and aerosols down to .75 micron, are 
trapped.  Both gases, air and O2, pass through sintered metal filters. 

Supply pressures are monitored and displayed by the ventilator via pressure 
transducers and the system electronics.  The system will trigger an alarm if either Air 
or O

2

 pressure drops below 24(±2) psig, and the alarm will reset when the pressures 

are above 30 psig. 

From the Air Inlet Water Trap and internal filters, the air and oxygen enter the in-line, 
one way Check Valves which prevent flow from exiting through an inlet if that source 
is removed. 

Blender 

Air and O

2

 pressure are regulated to 17 psig and are balanced to each other for 

accurate blending of gases in the O

2

 blender. 

In the event of a failure of either of the supply gases, one of a pair of crossover 
check valves will open to permit continued operation.  Oxygen blending will not be 
maintained in this condition, and the patient gas flow and pressure may decrease, by 
less than 10%, depending on settings.  

To ensure accurate oxygen blending at low patient flow rates, a bleed valve 
maintains a minimum flow through the blender. 

Flow Control Valve 

Two flow control valves are switched by a solenoid valve to create Inspiratory and 
Base Flow. Each valve controls flow from 1 to 30 L/min.  Each flow control valve is 
geared to a potentiometer.  The potentiometer provides an electronic signal to the 
microprocessor; this flow is then displayed on the front panel corrected to set 
barometric pressure. 

L2346 

Revision B 

June 2004 

Содержание Bear Cub 750PSV



































































































Отзывы:

Нет отзывов