VIA Technologies EPIA-M860-12E Скачать руководство пользователя | Manualshive

Страница: 60 / 84

background image

EPIA-M860 User Manual

49

6.5.6.

APM Configuration

APM enables the operating system to co-work with the BIOS to control the system power management. The APM
Configuration screen can be used to set a number of power management functions.

Figure 51: Illustration of APM Configuration screen

6.5.6.1.

Power Button Mode

The Power Button Mode has three options.

On/Off
When On/Off is selected, pressing the power button will instantly cause the system to power on or off.

Standby
When Standby is selected, the power button must be pressed and held down for 4 seconds before the system will
power off.

Suspend
When Suspend is selected, pressing the power button will instantly cause the system to enter suspend mode.

6.5.6.2.

Restore on AC/Power Loss

Restore on AC/Power Loss defines how the system will respond after AC power has been interrupted while the system
is on. There are three options.

Power Off
The Power Off option keeps the system in an off state until the power button is pressed again.

Power On
The Power On option restarts the system when the power has returned.

Last State
The Last State option restores the system to its previous state when the power was interrupted.

6.5.6.3.

Resume on PS/2 KBC

Resume on PS/2 KBC wakes up a system that has been put into suspend or standby mode. When this feature is enabled,
keyboard activity as defined in the Wake-Up Key feature will cause the system to wake up. This feature has three options.

S3
The S3 option enables PS/2 keyboard activity to be detected if the system is in S3 power saving mode.

S3/S4/S5
The S3/S4/S5 option enables PS/2 keyboard activity to be detected if the system is in S3/S4/S5 power saving mode.

Disabled
The Disabled option disables the detection of all PS/2 keyboard activity.

«
...
58
59
60
61
62
...
»

Содержание EPIA-M860-12E





















































































Отзывы:

Нет отзывов

Похожие инструкции для EPIA-M860-12E

Advanced Socket 370

Бренд: BCM Advanced Research Страницы: 38

Бренд: Quick Страницы: 32

Бренд: JETWAY Страницы: 38

Бренд: ASROCK Страницы: 2

Бренд: Sure Electronics Страницы: 32

Бренд: Ublox Страницы: 38

Бренд: MSI Страницы: 71

Бренд: Texas Instruments Страницы: 14

790XT-G35 series

Бренд: MSI Страницы: 103

Бренд: Gigabyte Страницы: 81

Бренд: Qiyangtech Страницы: 16

Бренд: EPC Страницы: 10

Бренд: Thinklabs Страницы: 129

Бренд: Biostar Страницы: 40

Бренд: TYAN Страницы: 118

Бренд: ECS Страницы: 70

Бренд: DFI Страницы: 73

Бренд: DFI Страницы: 82

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды