Vezco PRO-NVR-Smart Скачать руководство пользователя страница 3

Quick Start Guide of PRO-NVR-Smart 

Regulatory Information 

FCC Information 

Please  take  attention  that  changes  or  modification  not  expressly  approved  by  the  party 
responsible for compliance could void the user’s authority to operate the equipment. 

FCC compliance: 

This equipment has been tested and found to comply with the limits for a 

Class  B  digital  device,  pursuant  to  part  15  of  the  FCC  Rules.  These  limits  are  designed  to 

provide  reasonable  protection  against  harmful  interference  in  a  residential  installation.  This 

equipment generates, uses  and  can radiate  radio frequency energy and, if not installed and 

used  in  accordance  with  the  instructions,  may  cause  harmful  interference  to  radio 

communications. However, there is no guarantee that interference will not occur in a particular 

installation. If this equipment does cause harmful interference to radio or television reception, 

which can be determined by turning the equipment off and on, the user is encouraged to try to 

correct the interference by one or more of the following measures: 
—Reorient or relocate the receiving antenna. 
—Increase the separation between the equipment and receiver. 
—Connect the equipment into an outlet on a circuit different from that to which the receiver is 

connected. 
—Consult the dealer or an experienced radio/TV technician for help.

 

FCC Conditions 

This device complies with part 15 of the FCC Rules. Operation is subject to the following two 

conditions: 

1. This device may not cause harmful interference.

 

2. This device must accept any interference received, including interference that may cause 

undesired operation.

 

EU Conformity Statement 

This product and - if applicable - the supplied accessories too are marked with "CE" 

and  comply  therefore  with  the  applicable  harmonized  European  standards  listed 

under  the  EMC  Directive  2014/30/EU,  the  LVD  Directive  2014/35/EU,  the  RoHS  Directive 

2011/65/EU. 

 

2012/19/EU  (WEEE  directive):  Products  marked  with  this  symbol  cannot  be 

disposed  of  as  unsorted  municipal  waste  in  the  European  Union.  For  proper 

recycling, return this product to your local supplier upon the purchase of equivalent 

new  equipment,  or  dispose  of  it  at  designated  collection  points.  For  more  information  see: 

www.recyclethis.info

 

2006/66/EC  (battery  directive):  This  product  contains  a  battery  that  cannot  be 

disposed of as unsorted municipal waste in the European Union. See the product 

documentation  for  specific  battery  information.  The  battery  is  marked  with  this 

symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For 

proper  recycling,  return  the  battery  to  your  supplier  or  to  a  designated  collection  point.  For 

more information see: 

www.recyclethis.info 

Industry Canada ICES-003 Compliance 

This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements. 

Содержание PRO-NVR-Smart































Отзывы: