background image

9

REAR PANEL

51

52

54

46

45

53

48

50

49

47

56

55

44

43

$3

MIC1 INPUT JACK

Input jack for MIC.
MIC1: PHONE JACK (UNBALANCED)
MIC2: XLR JACK (BALANCED)

$4

EFFECT LOOP JACK

TIP: SEND OUT
RING: RETURN INPUT
SLEEVE: EARTH
Connects to the input of an external effects device.

$5

INPUT LEVEL SELECT SWITCH (0dB/-10dB)

Selects the attenuation level for any input signal.

$6

LINE INPUT RCA JACK

Input connectors for line level equipment such as CD
players, MD players, tape decks, DAT and/or VTR
etc.

$7

PHONO INPUT RCA JACK

Input jacks for turntables. Connect turntables
equipped with MM (pick up) cartridge.

$8

GND TERMINAL

Connect this terminal to the ground lead of the
turntable. This will help to reduce unnecessary noise.

$9

AUX SEND JACK

Connects to the input of external effects devices.
(Delay, Reverb, etc)

%0

AUX RCV JACK

Connects to the output of external effects devices.

%1

REC OUT JACK

Connects to the input jack of any recording device
IE, tape recorder, MD, DAT, etc. The output level of
this jack is fixed and does not change with the
MASTER LEVEL.

%2

MASTER OUT1&2(1/4" PHONE JACK
(UNBALANCED),XLR JACK(BALANCED)

Connect to the input on a power amplifier. These jacks are
Phone type for consumer applications.  This mixer has
two sets of MASTER OUT jacks so that the each output
level can be set separately.  Therefore, the MASTER
OUT can be used for main output or sub output IE.  One
for the main area and the other for entrance.

%3

BOOTH OUT(1/4" PHONE JACK
(UNBALANCED),XLR JACK(BALANCED)

Connects to the DJ booth monitors. 

In order to prevent feedback from booth monitors
in  a  typical  setting,  both  MIC1/LINE11  &
MIC2/LINE12  cannot  be  heard  thorough  the
booth  monitor  section.    These  2  PGMs  can
however  be  monitored  through  the  headphone
section.    An  internal  modification  is  needed  in
order to allow these a PGMs to be heard through
the  booth  monitor  section.    Please  consult  a
Vestax  Technical  Support  Representative  before
attempting any such modification.

%4

POWER SWITCH

Power on/off.

%5

POWER JACK

Connect the Vestax AC-20 , AC adaptor.

SEND

RETURN

EARTH

Содержание PMC 500

















Отзывы: