background image

--------------------------------------------------------------------------------------------------------------------------------------- 

12 

 

LIMITED WARRANTY: 

VESSEL expressly warrants that for a period of  one (1) year from the date of purchase, VESSEL static 

erasers will be free of defects in material (parts) and workmanship (labour). Within the warranty period, 

Defects occurring will be repaired or products will be replaced at VESSEL's option and expense, if VESSEL 

receives notice during the warranty period. Defective products must be returned to VESSEL Osaka Japan with 

proof of purchase date. And if your unit is out of warranty, VESSEL will quote repair charges necessary to ship 

your unit freight prepaid to where you have originally purchased. 

 

WARRANTY EXCLUSIONS: 

THE FOREGOING EXPRESS WARRANTY IS MADE IN LIEU OF ALL OTHER PRODUCT WARRANTIES, 

EXPRESSED AND IMPLIED, INCLUDING FITNESS AND MERCHANTABILITY AND FITNESS FOR A 

PARTICULAR PURPOSE WHICH ARE SPECIFICALLY DISCLAIMED. 

The express warranty will not apply to defects or damage due to accidents, neglect, misuse, alterations, 

operator error, or failure to properly maintain, clean, or repair products. 

 

LIMIT OF LIABILITY: 

This electronic static eraser use high voltage corona discharge and should not be used in or near 

flammable or explosive environments. In no event will VESSEL or any seller is responsible or liable for 

any injury, loss or damage, direct or consequential, whether based in tort or contract arising out of the 

use of or the inability to use the product. Fulfillment of VESSEL's warranty obligations will be 

Customer's exclusive remedy and VESSEL's and Seller's limit of liability for any breach of warranty or 

otherwise. Before using this unit, users shall determine the suitability of the product for their intended 

use, and users assume all risk and liability whatsoever in connection therewith. 

 

Model 

N-3 

 
 

Warranty 

(1) year from the date of purchase 

 

Customer 

Name 

 

Address 

 
 

Tel. No. 

 

Dealer 

Name/Address/Tel. No. 
 
 

 

Manufactured by: 

 

 

17-25, Fukae-Kita 2-chome, 

Higashinari-ku, Osaka  537-0001 Japan 

Tel : +81 6 6976 7778    Fax : +81 6 6972 9441 

E-mail : [email protected] 

URL : http://www.vessel.jp 

                                                                             

Printed in Japan 

2014073100.00000 

Abbeon Cal, Inc.

1363 Donlon Street Unit 1,  

Ventura, CA 93003-8387

800-922-0977   www.Abbeon.com     

E-mail:  [email protected]

Содержание STAT CLEAN N-3













Отзывы: