background image

13 

Procedures in Abnormal Conditions

Sparks from the electrode needles 

There should be no visible sparks from the static elimination device system during normal use. If you 
see these kinds of sparks continuing to occur at the electrode needles, etc., make sure to perform 
necessary maintenance such as cleaning them. If cleaning does not exclude the occurrence of 
sparks, stop the supply of power to the unit and contact the dealer from which the product was 
purchased. 
 

Other anomalies 

If any of the following phenomena occur, immediately stop the supply of power to the unit and 
contact the dealer from which the product was purchased. 
 

• Sparks are being emitted from the ionizer, part of the high voltage cable, etc. 
• The unit output connector, or part of the high voltage cable has melted.   

It is smoking or burning. 

• A strange smell is coming from the unit. 

• The unit is considerably distorted. 

• The unit is abnormally hot. (enough that it cannot be touched with bare hands) 

• It is making an unusual humming sound. (which can be easily heard from 1 

 away) 

• The power indicator light does not come on even though the power switch is turned to ON. 

 

 CAUTION

 

 

 

 

PROHIBITED

 

Do not use the product in the following conditions. Risk of fire or 

electric shock. 

• The product is broken due to dropping or shock. 
• The power indicator light does not come on even though the power 

switch is turned to ON. 

• The cord is damaged or heated up. 
• The plug to the connector or outlet is loose. 

 

UNPLUG 
POWER CABLE

 

When any abnormal condition is detected, turn off the power switch 
and pull out the power supply connector.

 

 

DO NOT 
DISASSEMBLE

 

Never disassemble the product. 

Continuously using the product during failure or abnormal conditions may lead to product 
breakdowns or accidents, so please request repairs in a timely manner. Contact the dealer from 
which the product was purchased for repairs. 

 
 
 

Содержание Stat Buster GP-1

















Отзывы: