manualshive.com logo in svg

Verve PANTERA, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Verve PANTERA Скачать руководство пользователя страница 41

Brake check 

1. Pull the brakes levers. At the end of their travel, they should not be in contact with the handlebar.

3. Once the adjustments have been carried out, it is essential that you test your brakes. 

4. For brake pad replacement contact a professional mechanic.

Disc brake can reach a very high temperature once they are operating. Do not touch them or you will get burned 

Dirty brakes pads and rotor can lead to a drastically reduced braking power. Make sure that the brake remains free 
from oil, dirt, moist or any other fluid. Dirty brake pads cannot be cleaned under any circumstances, but they need to 
be replaced. Instead, rotors can be cleaned with a special brake cleaner. 

2. Lift and spin the wheels. They should spin freely. If this is not the case, you will need to adjust the brake caliper. This is a 
complex operation that needs a lot of care: loosen the clamping bolts, fully tighten the brake lever and tighten the clamping 
bolts. If after this adjustment the wheel do not spin freely contact your local bicycle mechanic. 

Unusual noises during braking and/or notable change of the braking force are indications that the brake pads are 
worn down. Check the brake pads and replace them if necessary.

Disc brake  system require a run-in period before they reach optimal performance. It is possible that the braking 
power is very weak during first rides. It is recommended to ride with great caution during this run- in period. Do not 
keep the brakes pulled for long time as this will result in a brake pads glazing over, reducing their power and 
efficiency. 

Page 41

Содержание PANTERA


















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды