VERTO 50G272, Инструкция по эксплуатации

Страница: 13 / 84

13
Safe position of the direction selector switch ( 4 ) is in the middle, it
prevents accidental starting of the power tool.
• D rill cannot be started, when the switch is in this position.
• Use this position of the switch to change drills or bits.
• Before starting the tool make sure the position of the direction
selector switch (
4 ) is correct.
Do not change direction of rotation when the drill spindle is
rotating.
CHANGE OF GEAR
G ear switch ( 3 ) ( fig. F ) allows to increase the range of rotational
speed.
Gear I : small speed range, big torque
Gear II : wider speed range, small torque.
Set the gear switch in position appropriate for the works to perform.
When the switch is blocked and cannot move, turn the spindle
slightly.
Never change the gear switch position when drill is operating. It
may damage the power tool.
Long lasting drilling at low rotational speed of the spindle
may cause motor overheating. Provide regular breaks during
operation or let the tool operate at maximum speed with no load
for approximately 3 minutes.
OPERATION AND MAINTENANCE
MAINTENANCE AND STORAGE
• C leaning the device after each use is recommended.
• D o not use water or any other liquid for cleaning.
• C lean the drill with a dry cloth or blow with compressed air at low
pressure.
• D o not use any cleaning agents or solvents, they may damage
plastic parts.
• C lean ventilation holes in the motor casing regularly to prevent
device overheating.
• In case of excessive commutator sparking, have the technical
condition of carbon brushes of the motor checked by a qualified
person.
• Store the drill in a dry place, beyond reach of children.
QUICK RELEASE CHUCK REPLACEMENT
Quick-release chuck is screwed onto spindle of the drill and
additionally secured with a screw.
• Set the direction selector switch ( 4 ) in the middle position.
• Open jaws of quick release chuck ( 1 ) and unscrew the fixing screw
(left-hand thread) ( fig. G ).
• Install hexagonal key in the quick release chuck and tap the other
end of the key.
• Unscrew the quick release chuck.
• Installation of the quick release chuck is similar to deinstallation,
only the sequence of actions is reversed.
A ll defects should be repaired by service workshop authorized by
the manufacturer.
TECHNICAL PARAMETERS
RATED PARAMETERS
Cordless drill
Parameter Value
Battery voltage 10,8 V DC
Battery type Li-Ion
Battery capacity 1300 m A h
Range of idle rotational speed 0-350 / 0-1350 rpm
Range of quick release chuck 0,8-10 mm
Torque control range 1 – 18 plus drilling
Max. torque (soft drive) 19 Nm
Max. torque (hard drive) 35 Nm
Protection class III
Weight 1,1 kg
Year of production 2017
Charger
Parameter Value
Supply voltage 230 V AC
Power supply frequency 50 Hz
C harging voltage 13,5 V DC
Max. charging current 350 m A
Battery charging time 3-5 h
Protection class II
Weight 0,07 kg
Year of production 2017
NOISE LEVEL AND VIBRATION PARAMETERS
Information regarding noise and vibration
The following levels of emitted noise, such as emitted acoustic
pressure Lp
A
and acoustic power level Lw
A
and measurement
uncertainty K have been given in the instruction manual as defined
in the
E N 60745 standard.
The following vibration value (acceleration value) a
h
and
measurement uncertainty K have been determined as defined in the
E N 60745-2-1 standard.
The vibration level provided in this instruction manual have been
determined according to the measurement procedure as defined in
the
E N 60745 standard and can be used for comparison of power
tools. This can be used for preliminary assessment of exposure to
vibrations.
The provided vibration level is representative for main applications
of the power tool. If the power tool is used for other applications or
with other working tools, and if it is not sufficiently maintained, the
vibration level may vary. The aforementioned reasons may increase
the exposure to vibrations during the entire operating period.
In order to precisely estimate the exposure to vibrations, periods
should be accounted for, in which the power tool is switched off, or
when it is switched on, but not operated. Thus, the total exposure to
vibration may prove considerably lower.
A dditional safety measures should be taken to protect the user
against effects of vibrations, such as: maintenance of the power tool
and its working tools, ensuring proper temperature of the hands and
proper organisation of work.
Sound pressure level: Lp
A
= 67 dB( A ); K = 3 dB( A )
Sound power level: Lw
A
= 78 dB ( A ) ; K = 3 dB( A )
Vibration acceleration: a
h
= 1,9 m/s²; K =1,5 m/s²
ENVIRONMENT PROTECTION / CE
D o not dispose of electrically powered products with household
wastes, they should be utilized in proper plants. Obtain information on
waste utilization from your seller or local authorities. Used up electric
and electronic equipment contains substances active in natural
environment. Unrecycled equipment constitutes a potential risk for
environment and human health.