Vertical Express HD98 Скачать руководство пользователя страница 10

Страница: 10 / 46

Mechanical Installation and Adjustment

HD-98 Door Operator with OST

Vertical Express

Overview

(continued)

Figure 1 - Single Speed Door Operator

Mechanical Installation and Adjustment

Preparing the Door Operator

Installation and adjustment of the door operator is best accomplished from an upper landing. Place
the car top at a comfortable working height, and use the landing as a working platform.

1. Turn OFF, Lock, and Tag out the mainline disconnect.

2. Remove the door operator from the shipping carton and crate. Locate and store the bag of

parts.

3. Remove the cover from the rear of the operator by loosening the two top screws and the two

lower rear screws.

4. Inspect the wiring. Make sure all connections are secure.

5. Loosen the bolts holding the mechanical stops.

6. While observing the shaft containing the cams (inside the operator), rotate the drive wheel.

7. Check and adjust, as necessary, the tension of the 3 V belts between the drive wheel and the

jack shaft sheave. See Figure 2 on page 9.

a. Loosen the two bolts on the idler arm, and turn the locknut on the adjustment screw

(located at the end of the idler arm).

b. Securely tighten the idler arm bolts and the locknut.

Drive Arm Support

Drive Wheel

Jack Shaft Sheave

Adjustable Arm

Drive Arm

Connecting Arm

Intermediate Arm

Mechanical Stops

Pivot Arm

Motor

Содержание HD98















































Результаты поиска

Содержание HD98

Отзывы:

Похожие инструкции для HD98

Бренды по названию

Популярные бренды

Vertical Express HD98, Руководство пользователя

Результаты поиска

Содержание HD98

Отзывы:

Похожие инструкции для HD98

Бренды по названию

Популярные бренды