versa 055B Скачать руководство пользователя страница 11

11

General Specifications

These  heaters  are  design  certified  and  tested  under
the  requirements  of ANSI  Z21.56/CSA  4.7 American
National Standard / CSA standards for gas-fired pool
heaters. 

The heater is interchangeable and can be used either
indoors  or  outdoors.  The  appropriate  top  designated
for that type of use is required. If desired, the top can
be changed at a later date to change from outdoor to
indoor  or  vice  versa.  Millivolt  heaters  contain  a  self-
generating  electrical  system  operating  between  .25
and .75 volts.

Ambient Temperature Rating of

Heater Components

Millivolt Heater with Honeywell Gas Valve
+32°F to +175°F

Millivolt Heater with Robertshaw Gas Valve
0°F to +175°F

Electronic Ignition Heaters*
-32°F to +175°F
*Requires 120V or 240V power supply

Rated inputs are suitable for up to 2000 feet elevation.
For  elevations  above  2000  feet,  reduce  input  4%  for
each  1000  feet  above  sea  level,  as  high  elevation
reduces  combustion  performance.  For  Canada,
reduce  input  10%  when  installed  at  2000-4500  feet
elevation.

INSTALLATION

If your state is such, be sure your contractor bears the
appropriate  license.  Persons  not  qualified  shall  not
attempt  to  fix  this  equipment  nor  attempt  repairs
according to these instructions.

Code Requirements

Installation must be in accordance with local codes, or,
in the absence of local codes, with the latest editions
of the National Fuel Gas Code, ANSI Z223.1, and the
National Electrical Code, ANSI/NFPA 70; for Canada,
the latest edition of CAN/CGA B-149.

Base Installation

Heater must be mounted on a level surface. It can be
installed on combustible flooring. Heaters may not be
installed on carpeting.

Clearances

NOTE:

These  instructions  are  intended  for  use  by

qualified  personnel  only,  specifically  trained  and
experienced in the installation of this type of heating
equipment  and  related  system  components.
Installation  and  service  personnel  may  be  required
by some states to be licensed.

WARNING:

Improper  installation,  adjustment,

alteration, service or maintenance may damage the
equipment,  create  a  hazard  resulting  in
asphyxiation,  explosion  or  fire,  and  will  void  the
warranty.

NOTE:

The heater should not be located in an area

where possible water leakage will result in damage
to  the  area  adjacent  to  the  appliance  or  to  the
structure. When such locations cannot be avoided, it
is  recommended  that  a  suitable  drain  pan,
adequately  drained,  be  installed  under  the
appliance. The pan must not restrict combustion air
flow.

WARNING:

The  heater  shall  not  be  located  in  an

area where water sprinklers, or other devices, may
cause  water  to  spray  through  the  cabinet  louvers
and into the heater. This could cause heavy internal
rusting or damage some electrical components, and
this would void the warranty.

Содержание 055B





































Отзывы: