Vermont Castings Radiance RADVTBDSB Скачать руководство пользователя страница 4

4

4

20306759

Radiance

®

 Direct Vent Gas Heater 

Proposition 65 Warning:

 Fuels used in gas, wood-burning 

or  oil  fired  appliances,  and  the  products  of  combustion  of 

such fuels, contain chemicals known to the State of California 

to cause cancer, birth defects and other reproductive harm.

California Health & Safety Code Sec. 25249.6

 

Radiance Direct Vent

Certified to:

ANSI Z21.88-2014 / CSA 2.33-2014

Vented Gas Heaters 

Inspection

The state or local gas inspector of the side wall horizontally 

vented gas fueled equipment shall not approve the installa-

tion unless, upon inspection, the inspector observes carbon 

monoxide detectors and signage installed in accordance 

with the provisions of 248 CMR 5.08(2)(a)1 through 4.

Exemptions

The following equipment is exempt from 248 CMR 5.08(2)

(a)1 through 4:
•  The equipment listed in Chapter 10 entitled “Equipment 

Not Required To Be Vented" in the most current edition 

of NFPA 54 as adopted by the Board; and

• 

Product Approved side wall horizontally vented gas fu

-

eled equipment installed in a room or structure separate 

from the dwelling, building or structure used in whole or 

in part for residential purposes.

MANUFACTURER REQUIREMENTS

Gas Equipment Venting System Provided

When the manufacturer of Product Approved side wall hor-

izontally vented gas equipment provides a venting system 

design or venting system components with the equipment, 

the instructions provided by the manufacturer for installation 

of the equipment and the venting system shall include:
•  Detailed instructions for the installation of the venting 

system design or the venting system components; and

•  A complete parts list for the venting system design or 

venting system.

Gas Equipment Venting System NOT Provided

When the manufacturer of a Product Approved side wall 

horizontally vented gas fueled equipment does not provide 

the parts for venting the flue gases, but identifies “special 

venting systems", the following requirements shall be sat-

isfied by the manufacturer:

•  The referenced “special venting system" instructions 

shall be included with the appliance or equipment in-

stallation instructions; and

•  The “special venting systems" shall be Product Ap-

proved by the Board, and the instructions for that sys-

tem shall include a parts list and detailed installation 

instructions.

A copy of all installation instructions for all Product 

Approved side wall horizontally vented gas fueled equip

-

ment, all venting instructions, all parts lists for venting 

instructions, and/or all venting design instructions shall 

remain with the appliance or equipment at the completion 

of the installation.

IMPORTANT SAFETY INFORMATION
REQUIREMENTS FOR THE 

COMMONWEALTH OF MASSACHUSETTS

All gas fitting and installation of this heater shall only be 

done by a licensed gas fitter or licensed plumber.
For all side wall horizontally vented gas fueled equipment 

installed in every dwelling, building or structure used in 

whole or in part for residential purposes, including those 

owned or operated by the Commonwealth and where 

the side wall exhaust vent termination is less than seven 

(7) feet above finished grade in the area of the venting, 

including but not limited to decks and porches, the following 

requirements shall be satisfied:

Installation of Carbon Monoxide Detectors

At the time of installation of the side wall horizontal vented 

gas fueled equipment, the installing plumber or gas fitter 

shall observe that a hard wired carbon monoxide detec-

tor with an alarm  is installed on each additional level of 

the dwelling, building or structure served by the side wall 

horizontal  vented  gas  fueled  equipment.  It  shall  be  the 

responsibility of the property owner to secure the services 

of  qualified  licensed  professionals  for  the  installation  of 

hard wired carbon monoxide detectors.

In the event that the side wall horizontally vented gas fueled 

equipment is installed in a crawl space or an attic, the hard 

wired carbon monoxide detector with alarm and battery 

back-up may be installed on the next adjacent floor level.

In the event that the requirements of this subdivision can 

not be met at the time of completion of installation, the 

owner shall have a period of thirty (30) days to comply with 

the above requirements; provided, however, that during 

said thirty (30) day period, a battery operated carbon mon-

oxide detector with an alarm shall be installed.

Approved Carbon Monoxide Detectors

Each carbon monoxide detector as required in accordance 

with the above provisions shall comply with NFPA 720 and 

ANSI/UL 2034 listed and IAS certified.

Signage

A  metal  or  plastic  identification  plate  shall  be  per

-

manently mounted to the exterior of the building at a 

minimum height of eight (8) feet above grade directly in 

line with the exhaust vent terminal for the horizontally 

vented gas fueled heating appliance or equipment. The 

sign shall read, in print size no less than one-half (1/2) 

inch  in  size,  “GAS  VENT  DIRECTLY  BELOW,  KEEP 

CLEAR OF ALL OBSTRUCTIONS".

Содержание Radiance RADVTBDSB





























































Отзывы: