background image

26D3310 

3

10. This unit complies with ANSI Z21.11.2-2001 Unvented

Heaters.

11.  Do not install the heaters in a bathroom or bedroom.
12.  Correct installation of the ceramic fi ber logs, proper 

location of the heater, and annual cleaning are necessary 

to  avoid  potential  problems  with  sooting.  Sooting, 

resulting  from  improper  installation  or  operation, 

can  settle  on  surfaces  outside  the  fi replace.  See  log 

placement instructions for proper installation.

13.  Avoid any drafts that alter burner fl ame patterns. Do not 

allow fans to blow directly into fi replace. Do not place 

a blower inside burn area of fi rebox. Ceiling fans may 

create drafts that alter burner fl ame patterns. Sooting 

and improper burning will occur.

14. 

Caution:

  Candles,  incense,  oil  lamps,  etc.  produce 

combustion  byproducts  including  soot.  Vent-free 

appliances  will  not  fi lter  or  clean  soot  produced  by 

these types of products. In addition, the smoke and/or 

aromatics  (scents)  may  be  reburnt  in  the  vent-free 

appliance which can produce odors. It is recommended 

to minimize the use of candles, incense, etc. while the 

vent-free appliance is in operation. 

15.  This is an unvented gas-fi red heater. It uses air (oxygen) 

from  the  room  in  which  it  is  installed.  Provisions 

for adequate combustion and ventilation air must be 

provided. See page 10. 

16.  Keep  room  area  clear  and  free  from  combustible 

materials,  gasoline  and  other  fl ammable  vapors  and 

liquids.

INSTALLER

Please leave these instructions with the owner.

OWNER

Please retain these instructions for future reference.

IMPORTANT

Read these instructions carefully before installing or trying to operate this vent-free gas heater.

IMPORTANT SAFETY INFORMATION

  1.  Due  to  high  temperatures,  the  appliance  should 

be located out of traffi c and away from furniture 

and draperies.

  2.  Children and adults should be alerted to the hazard 

of high surface temperature and should stay away to 

avoid burns or clothing ignition.

  3.  Young children should be carefully supervised when 

they are in the same room with the appliance. 

  4.  Do not place clothing or other fl ammable material 

on or near the appliance. 

  5.  Any safety screen or guard removed for servicing 

an appliance, must be replaced prior to operating 

the heater.

  6.  Installation and repair should be done by a qualifi ed 

service person.

  7.  To prevent malfunction and/or sooting, an unvented 

gas heater should be cleaned before use and at least 

annually  by  a  professional  service  person.  More 

frequent cleaning may be required due to excessive 

lint  from  carpeting,  bedding  materials,  etc.  It  is 

imperative that control compartments, burners and 

circulating air passageways be kept clean.

  1.  Due  to  high  temperatures,  the  appliance  should 

  2.  Children and adults should be alerted to the hazard 

  3.  Young children should be carefully supervised when 

  4.  Do not place clothing or other fl ammable material 

  5.  Any safety screen or guard removed for servicing 

  6.  Installation and repair should be done by a qualifi ed 

  7.  To prevent malfunction and/or sooting, an unvented 

8.

  

CARBON MONOXIDE POISONING:

 Early signs of 

carbon monoxide poisoning are similar to the fl u with 

headaches, dizziness and/or nausea. If you have these 

signs, obtain fresh air immediately. Have the heater 

serviced as it may not be operating properly.

9.   The installation must conform with local codes or, in 

the absence of local codes, with the 

National Fuel Gas 

Code, ANSI Z223.l/NFPA54.

Continued on page 4

• Any change to this heater or its controls can be dangerous.
• Improper installation or use of the heater can cause serious injury or death from fi re, 

burns, explosion or carbon monoxide poisoning.

• Do  not  allow  fans  to  blow  directly  into  the  fi replace.  Avoid  any  drafts  that  alter 

burner fl ame patterns.

• Do not use a blower insert, heat exchanger insert or other accessory, not approved 

for use with this heater where applicable.

W

ARNING

Содержание DFS3224A









































Отзывы: