background image

3

Chateau™ Direct Vent Gas Fireplace

20011957

This gas fireplace should be installed by a qualified 
installer, preferably NFI or WETT (Canada) certified, in 
accordance with local building codes and with current CSA-
B149.1 Installation codes for Gas Burning Appliances and 
Equipment. For USA Installations follow local codes and/or 
the current National Fuel Gas Code. ANSI Z223.1/NFPA 54.

In the Commonwealth of Massachusetts:

•  All gas fitting and installation of this heater shall only be 

done by a licensed gas fitter or licensed plumber.

•  A carbon monoxide detector must be installed in the same 

room as the fireplace. (Refer to Regulation 248CMR 4.00 & 
5.00 for more information.)

FOR SAFE INSTALLATION AND OPERATION PLEASE NOTE 
THE FOLLOWING:
1.  This fireplace gives off high temperatures and should be 

located out of high traffic areas and away from furniture 
and draperies.

2.   Children and adults should be alerted to the hazards of the 

high surface temperatures of this fireplace and should stay 
away to avoid burns or ignition of clothing.

3.  

CAUTION: Due to high glass surface temperature chil-
dren should be carefully supervised when  in the same 
room as fireplace.

Installation & Operating Instructions

This  appliance  may  be  installed  in  an  aftermarket 
permanently located, manufactured home or mobile 
home, where not prohibited by local codes.
This appliance is only for use with the type of gas 
indicated on the rating plate. This appliance is not 
convertible for use with other gases, unless a certified 
kit is used. 
The DVT38S2 has been approved for mobile home 
installations.

Proposition 65 Warning:

 Fuels used in gas, woodburning or 

oil fired appliances, and the products of combustion of such 
fuels, contain chemicals known to the State of California to 
cause cancer, birth defects and other reproductive harm.
California Health & Safety Code Sec. 25249.6

IMPORTANT:

PLEASE REVIEW THE FOLLOWING CAREFULLY

Remove any plastic from parts before turning the 
fireplace ON.
It is normal for fireplaces fabricated of steel to give off 
some expansion and/or contraction noises during the 
start up or cool down cycle. Similar noises are found  
with your furnace heat exchanger or car engine.
It is not unusual for your gas fireplace to give off some 
odor the first time it is burned. This is due to the curing 
of the paint and any undetected oil from the manufac-
turing process.

Please ensure that your room is well ventilated-
open all windows.

It is recommended that you burn your fireplace for at 
least ten (10) hours the first time you use it. 

WARNING: Check with your electronics manufac-
turer before installing a television or other electronic 
device above this fireplace.

this fireplace must be installed on a metal or wood panel 
extending the full width and depth of the fireplace.

12.  This fireplace requires adequate ventilation and 

combustion air to operate properly.  

13. This fireplace must not be connected to a chimney flue 

serving a separate solid fuel burning fireplace.

14. When the fireplace is not in use it is recommended that the 

gas control valve be left in the 

“OFF”

 position.

DVT38S2

Certified To

ANSI Z21.50b-2005 / CSA 2.22b-2005 

Vented Gas Fireplace

�������

���������

�����

������������

������������

������

�������������

�����

���������������

���������������

4.   Under no circumstances should this fireplace be modified. 

Parts removed for servicing should be replaced prior to 
operating this fireplace again.

5.  A professional service person should be contacted to 

inspect the fireplace annually. More frequent cleaning may 
be required due to excess lint and dust from carpeting, 
bedding material, etc.

6.  Control compartments, burners and air passages in this 

fireplace should be kept clean and free of dust and lint. 
Make sure that the gas valve and pilot light are turned off 
before you attempt to clean this fireplace.

7.  The venting system (chimney) of this fireplace should be 

checked at least once a year and if needed your venting 
system should be cleaned.

8.  Keep the area around your fireplace clear of combustible 

materials, gasoline and other flammable vapor and liquids. 
This fireplace should not be used as a drying rack for cloth-
ing, nor should Christmas stockings or decorations be hung 
on or around the fireplace.

9.  Under no circumstances should any solid fuels (wood, coal, 

paper or cardboard etc.) be used in this fireplace.

10.  The flow of combustion and ventilation air must not be 

obstructed in any way.

11.  When the fireplace is installed directly on carpeting, 

vinyl tile or any combustible material other than wood, 

NOTE:

 We recommend that you install the Battery 

Back-up Kit, DVTBBK, which must be installed at the 
time of fireplace installation. The use of this kit will allow 
your fireplace to continue to operate in the event electric 
power is lost such as during a severe snow, ice or thun-
der storm. Refer to Item 16 on Page 8. 

Содержание Chateau DVT38S2IN

















































Отзывы: