Vermont Castings 300DVBHNSC7 страница 62 Скачать руководство пользователя

Страница: 62 / 64

DVBH7 Series Direct Vent Gas Fireplace

54D8001

Note ReGARDING VeNteD pRoDuctS

This product must be installed by a licensed plumber or gas fitter

when installed within the Commonwealth of Massachusetts.
Any residence with a direct vent product must have a CO

detector installed in the residence.
Installation of the fireplace or vented gas log in the State of

Massachusetts requires the damper to be permanently removed

or welded in the fully open position.
In addition, a naturally vented gas log may not be installed in a

bedroom or bathroom in the State of Massachusetts.
Flex line installation must not exceed 36 inches and must have

a T shutoff valve.

Note ReGARDING VeNt FRee pRoDuctS

This product must be installed by a licensed plumber or gas fitter

when installed within the Commonwealth of Massachusetts.
In addition, vent free products may not be installed in a

bedroom or bathroom regardless of size or type in the State of

Massachusetts.
Flex line installation must not exceed 36 inches and must have

a T shutoff valve.

cARBoN moNoxIDe DetectoR RequIRemeNtS

() Revise 10.8.3 by adding the following additional

requirements:
(a)

For all side wall horizontally vented gas fueled

equipment installed in every dwelling, building or structure used

in whole or in part for residential purposes, including those

owned or operated by the Commonwealth and where the side

wall exhaust vent termination is less than seven (7) feet above

finished grade in the area of the venting, including but not

limited to decks and porches, the following requirements shall

be satisfied:
1.

Installation of carbon monoxide detectors.

At the time

of installation of the side wall horizontal vented gas fueled

equipment, the installing plumber or gas fitter shall observe

that a hard wired carbon monoxide detector with an alarm and

battery back-up is installed on the floor level where the gas

equipment is to be installed. In addition, the installing plumber

or gas fitter shall observe that a battery operated or hard wired

carbon monoxide detector with an alarm is installed on each

additional level of the dwelling, building or structure served by

the side wall horizontal vented gas fueled equipment. It shall be

the responsibility of the property owner to secure the services of

qualified licensed professionals for the installation of hard wired

carbon monoxide detectors

a. In the event that the side wall horizontally vented gas

fueled equipment is installed in a crawl space or an attic, the

hard wired carbon monoxide detector with alarm and battery

back-up may be installed on the next adjacent floor level.

b. In the event that the requirements of this subdivision

can not be met at the time of completion of installation, the

owner shall have a period of thirty (30) days to comply with the

above requirements; provided, however, that during said thirty

(30) day period, a battery operated carbon monoxide detector

with an alarm shall be installed.

massachusetts Residents only — please read and follow these special requirements

Approved carbon monoxide Detectors.

Each carbon

monoxide detector as required in accordance with the above

provisions shall comply with NFPA 70 and be ANSI/UL 034

listed and IAS certified.
3.

Signage.

A metal or plastic identification plate shall be

permanently mounted to the exterior of the building at a

minimum height of eight (8) feet above grade directly in line with

the exhaust vent terminal for the horizontally vented gas fueled

heating appliance or equipment. The sign shall read, in print size

no less than one-half (1/) inch in size, “GAS VENT DIRECTLY

BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS.”
4.

Inspection.

The state or local gas inspector of the side wall

horizontally vented gas fueled equipment shall not approve the

installation unless, upon inspection, the inspector observes

carbon monoxide detectors and signage installed in accordance

with the provisions of 48 CMR 5.08()(a)1 through 4.
(b)

exemptions:

The following equipment is exempt from 48

CMR 5.08()(a)1 through 4:
1. The equipment listed in Chapter 10 entitled "Equipment Not

Required To Be Vented" in the most current edition of NFPA 54

as adopted by the Board; and
. Product Approved side wall horizontally vented gas fueled

equipment installed in a room or structure separate from the

dwelling, building or structure used in whole or in part for

residential purposes.
(c)

manufacturer requirements — Gas equipment Venting

System provided.

When the manufacturer of Product

Approved side wall horizontally vented gas equipment provides

a venting system design or venting system components with

the equipment, the instructions provided by the manufacturer

for installation of the equipment and the venting system shall

include:
1. Detailed instructions for the installation of the venting system

design or the venting system components; and
. A complete parts list for the venting system design or venting

system.
(d)

manufacturer requirements — Gas equipment Venting

System Not provided.

When the manufacturer of a Product

Approved side wall horizontally vented gas fueled equipment

does not provide the parts for venting the flue gases, but

identifies “special venting systems,” the following requirements

shall be satisfied by the manufacturer:
1. The referenced "special venting system" instructions shall

be included with the appliance or equipment installation

instructions; and
. The “special venting systems” shall be Product Approved by

the Board, and the instructions for that system shall include a

parts list and detailed installation instructions.
(e)

A copy of all installation instructions for all Product

Approved side wall horizontally vented gas fueled equipment,

all venting instructions, all parts lists for venting instructions,

and/or all venting design

Содержание 300DVBHNSC7

































































Результаты поиска

Содержание 300DVBHNSC7

Отзывы:

Похожие инструкции для 300DVBHNSC7

Бренды по названию

Популярные бренды

Vermont Castings 300DVBHNSC7, Руководство по установке и эксплуатации для владельцев жилья

Результаты поиска

Содержание 300DVBHNSC7

Отзывы:

Похожие инструкции для 300DVBHNSC7

Бренды по названию

Популярные бренды