TM
TM
E54C3C Installation Guide
E54C3C Installation Guide
Configuration (cont.)
Configuration Menu
All parameters in the configuration menu are modified in one of two ways.
1. Select a value from a pre-set list:
use the down button to scroll through the parameter values until the desired value is
reached. Press OK to confirm the selected value.
2. Modify a numerical value:
the digit on the far right is selected first. Use the down button to modify the selected digit.
Press OK to move to the next digit. Repeat for all available digits, then press OK to confirm the selected value.
To cancel the current entry, press the ESC button. This cancels the modification and the screen reverts to the last saved value.
A - Cancel and return to the
previous screen
B - Reset the settings to their
defaults, except for the
password, and restart the
meter.
Wiring
Wiring\Type
Wiring\VT
Wiring\CT
Wiring
Save settings?
OK
3PH4W
1PH2W L-N
...
Direct-NoPT
Wye(3PTs)
...
1 CT on I1
2 CTs on I1, I3
...
CT & VT Ratio
..\CT Secondary
..\CT Primary
..\VT Secondary
..\VT Primary
5
1
100
110
...
1
2 ...
0 - 99999
CT & VT Ratio
Save settings?
1
2 ...
0 - 9999999
Frequency
Frequency
50
60
Frequency
Save settings?
Date
Date
Date
Save settings?
1
2 ...
DD-MM-YYYY
Time
Time
Time
Save settings?
1
2 ...
hh:mm
T3 Start = T1 Start
T4 Start = T2 Start
Multi- Tariffs
..\Control Mode
..\Schedule
..\T1 Start
Multi Tariffs
Save settings?
Disable
by Digital Input
by Communications
by Internal Clock
..\T2 Start
1
2 ...
hh:mm
1
2 ...
hh:mm
by 2 Tariffs
by 3 Tariffs
...
Overload Alarm
..\Alarm
Disable
Enable
..\Pick Up Value
Overload Alarm
Save settings?
1
2 ...
0 - 9999999
Contrast
Contrast
Contrast
Save settings?
1
2
...
Com.Protection
Com.Protection
Com.Protection
Save settings?
Enable
Disable
Password
Password
Password
Save settings?
1
2 ...
1 - 9999
Reset Config
Reset Config
Confirm & Reboot?
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
Digital Input
..\DI Function
..\In. Pulse Const.
Digital Input
Save settings?
Input Status
Tariff Control
Partial Reset
Input Metering
1
2 ...
1 - 99999
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
Digital Output
..\DO Function
..\Pulse Constant
Digital Output
Save settings?
Disable
for Alarm
for Pulse
OK
OK
OK
OK
0.01
0.1
...
..\Pulse Width
100
200
...
OK
Communication
..\Slave Address
..\Baud Rate
1
2 ...
1-247
OK
OK
Communication
OK
OK
19200
38400
...
Save settings?
..\Parity
OK
ODD
EVEN
NONE
ESC
ESC
ESC
ESC
After performing basic configuration, navigate to the real-time data screens and verify that the readings are correct.
The terms “VT” (voltage transformer) and “PT” (potential transformer) are used interchangeably.
Troubleshooting
Code
Description
Solution
-
LCD display is not visible.
Check and adjust LCD contrast.
-
Push buttons do not function.
Restart the energy meter by powering off and powering on
again.
101
Metering stops due to an EEPROM error. Press
OK
to
display total energy consumption.
Enter configuration mode and implement Reset Config.
102
Metering stops due to a lack of a calibration table. Press
OK
to display total energy consumption.
Enter configuration mode and implement Reset Config.
201
Metering continues. Mismatch between frequency
settings and frequency measurements.
Correct the frequency settings according to the nominal
frequency of the power system.
202
Metering continues. Mismatch between wiring settings
and wiring inputs.
Correct the wiring settings according to the wiring inputs.
203
Metering continues. Phase sequence reversed.
Check the wire connections and correct the wiring settings if
needed.
204
Metering continues. Total active energy negative due to
incorrect voltage and current conditions.
Check wire connections.
205
Metering continues. Date and Time have been reset due to
a loss of power.
Set the Date and Time.
206
Metering continues. Pulse is missing due to overload on
energy pulse output.
Check the energy pulse output settings.
207
Metering continues. Abnormal internal clock function.
Restart the energy meter by powering off and powering on
again then reset the date and time.
Multi-Tariff Feature
The multi-tariff feature allows the meter to categorize energy consumption by peak times vs. off-peak times and by weekdays
vs. weekends. The following table illustrates how the tariffs operate according to the tariff selection (2, 3 or 4 tariffs). These
tariffs are stored in four different registers: T1, T2, T3, and T4.
Weekday
Weekend
24 H
T1
T2
24 H
T1
T2
24 H
T1
T2
24 H
T1
T2
24 H
T3
24 H
T3
T4
2 Tariffs
3 Tariffs
4 Tariffs
ZL0131-0G Page 7 of 8 ©2018 Veris Industries USA 800.354.8556 or +1.503.598.4564 / [email protected] 0818
Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Aerospond, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries.
Other companies’ trademarks are hereby acknowledged to belong to their respective owners.
EAV71194-04
ZL0131-0G Page 8 of 8 ©2018 Veris Industries USA 800.354.8556 or +1.503.598.4564 / [email protected] 0818
Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Aerospond, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries.
Other companies’ trademarks are hereby acknowledged to belong to their respective owners.
EAV71194-04
