![background image](http://html1.mh-extra.com/html/veris-industries/e51h2a/e51h2a_installation-manual_1004653023.webp)
ZL0123-0D
Page 23 of 32
©2018 Veris Industries USA 800.354.8556 or +1.503.598.4564 / [email protected] 0818
Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Aerospond, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries.
Other companies’ trademarks are hereby acknowledged to belong to their respective owners.
TM
Installation Guide
Power Monitoring
Property
R/W
NV
Value Returned
Additional information
Object_List
R
NV
DE1,AI1,AI2,AI3,AI4,AI5,AI6,AI7,AI8,AI9,AI1
0,AI11,AI12,AI13,AI14,AI15,AI16,AI17,AI1
8,AI19,AI20,AI21,AI22,AI23,AI24,AI25,AI2
6,AI27,AI28,AI29,AI30,AI31,AI32,AI33,AI3
4,AI35,AI36,AI37,AI38,AI39,AI40,AI41,AI4
2,AI43,AI44,AI45,AI46,AI47,AI48,AI49,AI5
0,AI51,AI52, AI53, AI54, AI55, AI56, AI57,
AI58, AI59, AI60, AI61, AI62, AI63, AI64,
AI65, AI66, AI67, AI68, AI69, AI70, AI71,
AI72, AI73, AI74, AI75, AI76, AI77, AI78,
AI79, AI80, AI81, AI82, AI83, AV1,AV2,AV3,
AV4,AV5,AV6,AV7,AV8,AV9,AV10,AV11,BI1
,BI2,BI3,BI4,BI5,BI6,BI7,BI8,BI9,BI10,BI11,
BI12,BI13,BI14,BI15,TL1,TL2,TL3
BI15, TL1, TL2, and TL3 are present on the E51H5A only.
Device_Address_Binding
R
NV
{}
Database_Revsion
R
NV
0
Analog_Value
Objects
Use the Present_Value property of the Analog_Value object for all writable variables in the meter other than those used
specifically for BACnet configuration, Time Synchronization (in the Device Object), or Data Logging (in the Trend_Log objects).
Values are checked when written, and errors are returned for invalid entries. This table describes how the meter uses those
variables, what values are valid, and what their defaults are. When writing values to the Present_Value properties of Analog_
Value BACnet objects, there is a delay of up to about two seconds to validate and store the new value. An immediate read of the
same property before that delay has elapsed can return the prior value (even if the new value was accepted). To read a value
immediately after writing it, check the Reliability property first. When it reports a No_Fault_Detected status, the Present_Value
of the object is current.
These objects support the Description and Reliability object properties and all required Analog_Value object properties, but
Present_Value is the only writable property.
#
Name
Description R/W
NV
Units
Range
Factory
Default
Value
Additional information
AV1
Config
Configuration R/W
n/a
n/a
Always
returns
”0” when
read
Command Register:
- Write 30078 (0x757E) to clear all energy accumulators to 0 (All).
- Write 21211 (0x52DB) to begin new Demand Sub-Interval calculation cycle and log
another data value on Trend_Log objects TL1-TL3 (when the meter is in Manual “Sync-
to Comms” mode). This takes effect at the end of the next 1 second calculation cycle.
Write no more frequently than every 10 seconds. Trend_Log values are only present on
the E51H5A model.
- Write 21212 (0x52DC) to reset Max Demand values to Present Demand Values. Takes
effect at the end of the next 1 second calculation cycle. Write no more frequently than
every 10 seconds.
- Write 16498 (0x4072) to clear pulse counters to 0.
AV2
System_Type System Type
R/W
NV
n/a
40, 31, 12,
11, 10
40
System_Type:
- Write 10 for Single-Phase: A + N
- Write 11 for Single-Phase: A + B
- Write 12 for Split-Phase: A + B + N
- Write 31 for 3-Phase Δ: A + B + C, no N
- Write 40 for 3-Phase Y: A + B + C + N
AV3
CT_Ratio_
Primary
CT Ratio -
Primary
R/W
NV
Amps
5-5000
100
Current Transducer Size - Primary Current Range (Default is set for 100 A CTs)
AV5
PT_Ratio
PT Ratio
R/W
NV
Value
0.01 - 320.0
1
Potential Transformer Ratio - The default is 1.00 (1:1), which is no PT attached. Set this
value before setting the System Voltage (below).
Device Object (cont.)